1
vote
0answers
201 views

MOC3010 & BT136 with Arduino as trigger to power AC light

I've spend days debugging this circuit and have exhausted all possible solutions. I'm trying to use an Arduino PWM pin to light a 120V AC lightbulb. In order to do this I'm using a MOC3010 ...
2
votes
0answers
166 views

Controlling Triac w/optocoupler, need some help with optocoupler datasheet

Loads: Some baseboard heaters (1500W max, some motors, 12A max). I have no experience using Triacs and optocouplers. Triac: T3035H-6T, Datasheet: ...
0
votes
0answers
106 views

Relay/TRIAC for water heater switching

I'm designing a remote controlled switch for my water heater and I am bothered by the following questions: Should the switch be DPST, or can I just switch the phase line (dangerous?) ? can I do it ...
2
votes
0answers
267 views

Using optoisolator and triac with mcu to switch light on/off--need low power alternative

I'm using the schematic below to control a lamp (light bulb) with a microcontroller and I'm running the mcu (and moc3010) off of AA batteries. I just realized the moc3010 has an LED in it that needs ...
2
votes
1answer
447 views

why does the microcontroller pin driving optocoupler is giving 2V even if it is set?

I have interfaced pin 1^1 of Atmel AT89S51 to optocoupler MOC3041 IC, I set this pin to logic high. I have connected 220 ohm resistor and red led and then pin 1 of the optocoupler and after that ...
2
votes
1answer
360 views

Controlling multiple triacs with microcontroller for light dimming: where to use optoisolators

I want to control (dim) multiple mains lights using triacs and a microcontroller. (One triac per light). I want to keep both the costs and component count as low as possible. Is it necessary to have ...
2
votes
1answer
205 views

Isolated vs non-isolated triacs

Bt136-600 is an example of a non-isolated triac, while BTA08 is an example of an insulated triac. What is the difference between an isolated and non-isolated triac? They seem to have the same symbol ...
1
vote
1answer
611 views

How do I select an optoisolator to both provide zero crossing to a uC and controll a triac?

This application note states that zero crossing detection can be achieved in an AVR with just a couple of resistors. However, it forgoes galvanic isolation and this is not acceptable for me. I would ...
10
votes
4answers
857 views

Validate Triac circuit

I'm designing a device to switch a heating device driven by mains power. I've done quite a lot of research and realize there's a lot of information out there but as i'm dealing with potentially deadly ...
2
votes
1answer
317 views

Why do they add a TRIAC after an MCP3020 optocoupler?

I have a relay circuit (I use it instead of a relay) that uses a MCP3020, which I think does the physical separation of the two circuits (it's a LED and a photo cell inside a chip) and a BTA08 TRIAC. ...
0
votes
1answer
182 views

Triac datasheet values

I have a Triac that I want to use to control low voltage (~16 V) AC. The data sheet is found here. It specifies that the peak gate voltage is 5 V with a peak current rating of 2 A (which seems quite ...
2
votes
1answer
236 views

Calculating max wattage load for opto-triac

Are there any guidelines? Do the guidelines differ depending on resistive/inductive/reactive loads? For example, the Vishay VO2223A is rated up to 1A. At 110V it seems it can switch up to a 1 A x ...
6
votes
3answers
3k views

TRIAC dimmer, circuit design help (resistive load)

Okay guys, I've been tasked with making a light-dimming control system for a 240V heat lamp dissipating around 250W. I need to adjust the heat output on the lamp by control from a microprocessor. I'm ...
1
vote
1answer
299 views

Do multi-channel opto-triacs with common pins exist?

I am designing a circuit with many (4-128) copies of the same component. It's a 4-pin opto-isolator with opto-triac output. I am aware that the pin spacing and package width can't be much less in ...
9
votes
4answers
11k views

Digital Dimmer With Microcontroller

I want to build a digital dimmer for resistive Loads. I have found this circuit for that: The input voltage is 220VAC 50Hz. The red box in the picture is for ...
6
votes
3answers
6k views

When should I fire the TRIAC's gate when controlling an inductive load (AC motor)?

I'm using a combination of opto-triac + TRIAC to control a 230V AC motor with a microcontroller. For detecting the zero-crossing of the voltage I'm using another optocoupler. I know that the AC ...
1
vote
2answers
825 views

What does 'random phase' means in a triac driver?

I'm using this triac driver to control a triac. In its datasheet it says 'provide random phase control of high current triacs [...]'. What does that mean? It doesn't have zero-crossing detection?
5
votes
2answers
1k views

Is a protection diode needed on a TRIAC optocoupler and what for?

Please refer to page nine of the Sharp S108T01 / S108T02 datasheet: Is this diode needed - why/why not? How do I choose the correct diode, if yes? UPDATE: Thank you all for your educational ...
4
votes
2answers
2k views

Difference between Zero-Crossing Optoisolator and Regular Optoisolator

I am trying to find any documentation on what the purpose is of a Zero-Crossing Circuit TRIAC Optoisolator. The datasheets don't explain the concept well enough. If you do answer, please include ...
1
vote
1answer
4k views

Choosing components for a triac's snubber

I'm interfacing the BT139-600 TRIAC with this MOC3051-M Opto-triac. I want to build a snubber circuit for the TRIAC as shown in the MOC3051M opto-triac's datasheet @ page 8, figure 12. The load ...
4
votes
4answers
1k views

Sanity-check on snubber design

I keep frying resistors in the following optocoupler and triac snubber circuit, and I'm not sure whether to attribute this to bad design, or to faulty components. There are no observable sparks at ...
10
votes
2answers
1k views

Why Snub an Optoisolator?

I am using an optocoupler and a power triac to switch 120VAC supply to an ~108 watt fan. The datasheet for my optocoupler requires me to snub the optocoupler output when I'm switching an inductive ...
2
votes
1answer
3k views

How to use a phototriac coupler to trigger the main triac?

I have in my box of parts a phototriac coupler, namely a Sharp PC3SD21NTZ (datasheet), which is a zero cross type. I don't know how to use it, but I've been meaning to learn for a while. This part is ...