Tweeted twitter.com/#!/StackElectronix/status/490060413615484928
5 added 133 characters in body
source | link

Some of our boards have a damaged SCR. I just witnessed one in person today. The SCR actually exploded upon power-on. A part of its packaging material just flew off along with an exploding sound. The resulting dead body of the SCR is shown here:

SCR in Pieces

I have a few questions about the circuit:

Schematic

Q1 (S6020L) is the SCR in question. It is rated 600V, 20A. AC input is 220V. What I did is:

  1. Remove AC/Power off.
  2. Discharge C5
  3. Power on. At the very same moment, Q1 exploded in pieces.

If the SCR is turned on when the rectified AC signal is right near its peak and the voltage at C5 is close to zero, I would imagine there is a huge inrush current to charge up the big capacitor.

The questions I am having are:

  1. How do I calculate the magnitude and duration of this inrush current.
  2. Does this inrush current exceed the specification of this particular SCR?

The rectifying bridge, GBJ2006, is not damaged in this case.

We have produced and sold a few hundred boards. There have been some occurrences of this problem. I am wondering if we should somehow change the design (I am not a hardware guy).

The SCR in question is not really from Littelfuse, but it matches S6020L in specification, as I heard from our hardware designer. I have no idea what manufacturer it is from and trying to determine if it is a design issue or a part quality problem.

The MCU (not in the schematics attached) sees the SYNC signal and triggers the SCR at appropriate times to ramp up the voltage at C5. This way the inrush current would be reduced considerably. The problem is that before my software takes charge, there may a glitch that triggers MOC3052M upon power-on. This is a one time thing and after that the software takes full control. I am having the doubt about the quality of the SCR part because this inrush current is not repetitive. The moment I witnessed the SCR explosion is without any load and right at the switch-on of the power switch. I know the obvious solution is to get rid of the glitch; however, I just want to know if this part is faulty.

HV_Bus (C5) is connected to a 1.25-HP motor, whose other terminal is connected to a MOSFET. MCU will turn on and off the MOSFET with a PWM signal and C5 gets discharged with this load. When the PWM signal is active, MCU triggers the SCR with a 2kHz frequency and keeps C5 charged.


AC mains hazards:

enter image description here

Some of our boards have a damaged SCR. I just witnessed one in person today. The SCR actually exploded upon power-on. A part of its packaging material just flew off along with an exploding sound. The resulting dead body of the SCR is shown here:

SCR in Pieces

I have a few questions about the circuit:

Schematic

Q1 (S6020L) is the SCR in question. It is rated 600V, 20A. AC input is 220V. What I did is:

  1. Remove AC/Power off.
  2. Discharge C5
  3. Power on. At the very same moment, Q1 exploded in pieces.

If the SCR is turned on when the rectified AC signal is right near its peak and the voltage at C5 is close to zero, I would imagine there is a huge inrush current to charge up the big capacitor.

The questions I am having are:

  1. How do I calculate the magnitude and duration of this inrush current.
  2. Does this inrush current exceed the specification of this particular SCR?

The rectifying bridge, GBJ2006, is not damaged in this case.

We have produced and sold a few hundred boards. There have been some occurrences of this problem. I am wondering if we should somehow change the design (I am not a hardware guy).

The SCR in question is not really from Littelfuse, but it matches S6020L in specification, as I heard from our hardware designer. I have no idea what manufacturer it is from and trying to determine if it is a design issue or a part quality problem.

The MCU (not in the schematics attached) sees the SYNC signal and triggers the SCR at appropriate times to ramp up the voltage at C5. This way the inrush current would be reduced considerably. The problem is that before my software takes charge, there may a glitch that triggers MOC3052M upon power-on. This is a one time thing and after that the software takes full control. I am having the doubt about the quality of the SCR part because this inrush current is not repetitive. The moment I witnessed the SCR explosion is without any load and right at the switch-on of the power switch. I know the obvious solution is to get rid of the glitch; however, I just want to know if this part is faulty.

HV_Bus (C5) is connected to a 1.25-HP motor, whose other terminal is connected to a MOSFET. MCU will turn on and off the MOSFET with a PWM signal and C5 gets discharged with this load. When the PWM signal is active, MCU triggers the SCR with a 2kHz frequency and keeps C5 charged.

Some of our boards have a damaged SCR. I just witnessed one in person today. The SCR actually exploded upon power-on. A part of its packaging material just flew off along with an exploding sound. The resulting dead body of the SCR is shown here:

SCR in Pieces

I have a few questions about the circuit:

Schematic

Q1 (S6020L) is the SCR in question. It is rated 600V, 20A. AC input is 220V. What I did is:

  1. Remove AC/Power off.
  2. Discharge C5
  3. Power on. At the very same moment, Q1 exploded in pieces.

If the SCR is turned on when the rectified AC signal is right near its peak and the voltage at C5 is close to zero, I would imagine there is a huge inrush current to charge up the big capacitor.

The questions I am having are:

  1. How do I calculate the magnitude and duration of this inrush current.
  2. Does this inrush current exceed the specification of this particular SCR?

The rectifying bridge, GBJ2006, is not damaged in this case.

We have produced and sold a few hundred boards. There have been some occurrences of this problem. I am wondering if we should somehow change the design (I am not a hardware guy).

The SCR in question is not really from Littelfuse, but it matches S6020L in specification, as I heard from our hardware designer. I have no idea what manufacturer it is from and trying to determine if it is a design issue or a part quality problem.

The MCU (not in the schematics attached) sees the SYNC signal and triggers the SCR at appropriate times to ramp up the voltage at C5. This way the inrush current would be reduced considerably. The problem is that before my software takes charge, there may a glitch that triggers MOC3052M upon power-on. This is a one time thing and after that the software takes full control. I am having the doubt about the quality of the SCR part because this inrush current is not repetitive. The moment I witnessed the SCR explosion is without any load and right at the switch-on of the power switch. I know the obvious solution is to get rid of the glitch; however, I just want to know if this part is faulty.

HV_Bus (C5) is connected to a 1.25-HP motor, whose other terminal is connected to a MOSFET. MCU will turn on and off the MOSFET with a PWM signal and C5 gets discharged with this load. When the PWM signal is active, MCU triggers the SCR with a 2kHz frequency and keeps C5 charged.


AC mains hazards:

enter image description here

4 Added how the SCR is triggered and how C5 is discharged
source | link

Some of our boards have a damaged SCR. I just witnessed one in person today. The SCR actually exploded upon power-on. A part of its packaging material just flew off along with an exploding sound. The resulting dead body of the SCR is shown here:

SCR in Pieces

I have a few questions about the circuit:

Schematic

Q1 (S6020L) is the SCR in question. It is rated 600V, 20A. AC input is 220V. What I did is:

  1. Remove AC/Power off.
  2. Discharge C5
  3. Power on. At the very same moment, Q1 exploded in pieces.

If the SCR is turned on when the rectified AC signal is right near its peak and the voltage at C5 is close to zero, I would imagine there is a huge inrush current to charge up the big capacitor.

The questions I am having are:

  1. How do I calculate the magnitude and duration of this inrush current.
  2. Does this inrush current exceed the specification of this particular SCR?

The rectifying bridge, GBJ2006, is not damaged in this case.

We have produced and sold a few hundred boards. There have been some occurrences of this problem. I am wondering if we should somehow change the design (I am not a hardware guy).

The SCR in question is not really from Littelfuse, but it matches S6020L in specification, as I heard from our hardware designer. I have no idea what manufacturer it is from and trying to determine if it is a design issue or a part quality problem.

The MCU (not in the schematics attached) sees the SYNC signal and triggers the SCR at appropriate times to ramp up the voltage at C5. This way the inrush current would be reduced considerably. The problem is that before my software takes charge, there may a glitch that triggers MOC3052M upon power-on. This is a one time thing and after that the software takes full control. I am having the doubt about the quality of the SCR part because this inrush current is not repetitive. The moment I witnessed the SCR explosion is without any load and right at the switch-on of the power switch. I know the obvious solution is to get rid of the glitch; however, I just want to know if this part is faulty.

HV_Bus (C5) is connected to a 1.25-HP motor, whose other terminal is connected to a MOSFET. MCU will turn on and off the MOSFET with a PWM signal and C5 gets discharged with this load. When the PWM signal is active, MCU triggers the SCR with a 2kHz frequency and keeps C5 charged.

Some of our boards have a damaged SCR. I just witnessed one in person today. The SCR actually exploded upon power-on. A part of its packaging material just flew off along with an exploding sound. The resulting dead body of the SCR is shown here:

SCR in Pieces

I have a few questions about the circuit:

Schematic

Q1 (S6020L) is the SCR in question. It is rated 600V, 20A. AC input is 220V. What I did is:

  1. Remove AC/Power off.
  2. Discharge C5
  3. Power on. At the very same moment, Q1 exploded in pieces.

If the SCR is turned on when the rectified AC signal is right near its peak and the voltage at C5 is close to zero, I would imagine there is a huge inrush current to charge up the big capacitor.

The questions I am having are:

  1. How do I calculate the magnitude and duration of this inrush current.
  2. Does this inrush current exceed the specification of this particular SCR?

The rectifying bridge, GBJ2006, is not damaged in this case.

We have produced and sold a few hundred boards. There have been some occurrences of this problem. I am wondering if we should somehow change the design (I am not a hardware guy).

The SCR in question is not really from Littelfuse, but it matches S6020L in specification, as I heard from our hardware designer. I have no idea what manufacturer it is from and trying to determine if it is a design issue or a part quality problem.

Some of our boards have a damaged SCR. I just witnessed one in person today. The SCR actually exploded upon power-on. A part of its packaging material just flew off along with an exploding sound. The resulting dead body of the SCR is shown here:

SCR in Pieces

I have a few questions about the circuit:

Schematic

Q1 (S6020L) is the SCR in question. It is rated 600V, 20A. AC input is 220V. What I did is:

  1. Remove AC/Power off.
  2. Discharge C5
  3. Power on. At the very same moment, Q1 exploded in pieces.

If the SCR is turned on when the rectified AC signal is right near its peak and the voltage at C5 is close to zero, I would imagine there is a huge inrush current to charge up the big capacitor.

The questions I am having are:

  1. How do I calculate the magnitude and duration of this inrush current.
  2. Does this inrush current exceed the specification of this particular SCR?

The rectifying bridge, GBJ2006, is not damaged in this case.

We have produced and sold a few hundred boards. There have been some occurrences of this problem. I am wondering if we should somehow change the design (I am not a hardware guy).

The SCR in question is not really from Littelfuse, but it matches S6020L in specification, as I heard from our hardware designer. I have no idea what manufacturer it is from and trying to determine if it is a design issue or a part quality problem.

The MCU (not in the schematics attached) sees the SYNC signal and triggers the SCR at appropriate times to ramp up the voltage at C5. This way the inrush current would be reduced considerably. The problem is that before my software takes charge, there may a glitch that triggers MOC3052M upon power-on. This is a one time thing and after that the software takes full control. I am having the doubt about the quality of the SCR part because this inrush current is not repetitive. The moment I witnessed the SCR explosion is without any load and right at the switch-on of the power switch. I know the obvious solution is to get rid of the glitch; however, I just want to know if this part is faulty.

HV_Bus (C5) is connected to a 1.25-HP motor, whose other terminal is connected to a MOSFET. MCU will turn on and off the MOSFET with a PWM signal and C5 gets discharged with this load. When the PWM signal is active, MCU triggers the SCR with a 2kHz frequency and keeps C5 charged.

3 Fix abuse of "literally"
source | link

SCR in this circuit literally exploded - why?

Some of our boards have a damaged SCR. I just witnessed one in person today. The SCR, actually exploded upon power-on, literally exploded. A part of its packaging material just flew off along with an exploding sound. TheThe resulting dead body of the SCR is shown here:

SCR in Pieces

I have a few questions about the circuit:

Schematic

Q1 (S6020L) is the SCR in question. It is rated 600V, 20A. AC input is 220V. What I did is:

  1. Remove AC/Power off.
  2. Discharge C5
  3. Power on. At the very same moment, Q1 exploded in pieces.

If the SCR is turned on when the rectified AC signal is right near its peak and the voltage at C5 is close to zero, I would imagine there is a huge inrush current to charge up the big capacitor.

The questions I am having are:

  1. How do I calculate the magnitude and duration of this inrush current.
  2. Does this inrush current exceed the specification of this particular SCR?

The rectifying bridge, GBJ2006, is not damaged in this case.

We have produced and sold a few hundred boards. ThereThere have been some occurrences of this problem. II am wondering if we should somehow change the design (I am not a hardware guy).

The SCR in question is not really from Littelfuse, but it matches S6020L in specification, as I heard from our hardware designer. I have no idea what manufacturer it is from and trying to determine if it is a design issue or a part quality problem.

SCR in this circuit literally exploded - why?

Some of our boards have a damaged SCR. I just witnessed one in person today. The SCR, upon power-on, literally exploded. A part of its packaging material just flew off along with an exploding sound. The resulting dead body of the SCR is shown here:

SCR in Pieces

I have a few questions about the circuit:

Schematic

Q1 (S6020L) is the SCR in question. It is rated 600V, 20A. AC input is 220V. What I did is:

  1. Remove AC/Power off.
  2. Discharge C5
  3. Power on. At the very same moment, Q1 exploded in pieces.

If the SCR is turned on when the rectified AC signal is right near its peak and the voltage at C5 is close to zero, I would imagine there is a huge inrush current to charge up the big capacitor.

The questions I am having are:

  1. How do I calculate the magnitude and duration of this inrush current.
  2. Does this inrush current exceed the specification of this particular SCR?

The rectifying bridge, GBJ2006, is not damaged in this case.

We have produced and sold a few hundred boards. There have been some occurrences of this problem. I am wondering if we should somehow change the design (I am not a hardware guy).

The SCR in question is not really from Littelfuse, but it matches S6020L in specification, as I heard from our hardware designer. I have no idea what manufacturer it is from and trying to determine if it is a design issue or a part quality problem.

SCR in this circuit exploded - why?

Some of our boards have a damaged SCR. I just witnessed one in person today. The SCR actually exploded upon power-on. A part of its packaging material just flew off along with an exploding sound. The resulting dead body of the SCR is shown here:

SCR in Pieces

I have a few questions about the circuit:

Schematic

Q1 (S6020L) is the SCR in question. It is rated 600V, 20A. AC input is 220V. What I did is:

  1. Remove AC/Power off.
  2. Discharge C5
  3. Power on. At the very same moment, Q1 exploded in pieces.

If the SCR is turned on when the rectified AC signal is right near its peak and the voltage at C5 is close to zero, I would imagine there is a huge inrush current to charge up the big capacitor.

The questions I am having are:

  1. How do I calculate the magnitude and duration of this inrush current.
  2. Does this inrush current exceed the specification of this particular SCR?

The rectifying bridge, GBJ2006, is not damaged in this case.

We have produced and sold a few hundred boards. There have been some occurrences of this problem. I am wondering if we should somehow change the design (I am not a hardware guy).

The SCR in question is not really from Littelfuse, but it matches S6020L in specification, as I heard from our hardware designer. I have no idea what manufacturer it is from and trying to determine if it is a design issue or a part quality problem.

2 Removed unnecessary signature (your signature is always at the bottom of the post).
source | link
1
source | link