Skip to main content
added 35 characters in body
Source Link
Ale..chenski
  • 42.4k
  • 3
  • 44
  • 113

It's the D+ and D- like normal. There is two of each because USB C is supposed reversible. You can insert the plug both ways and it will still be a valid USB 2 connection, as usb 2.0 does not negotiate the pinning. Flip the plug 180 degrees and the same pins will connect in the same order. Your board should connect both together for maximum connectivity.

There is no ID pin, as that's only implemented on plugs. In USB C, the CC pins handle this, and pulling them to ground with a 5K resistor will initiate OTG HOST mode on the other side of the link.

It's the D+ and D- like normal. There is two of each because USB C is supposed reversible. You can insert the plug both ways and it will still be a valid USB 2 connection, as usb 2.0 does not negotiate the pinning. Flip the plug 180 degrees and the same pins will connect in the same order. Your board should connect both together for maximum connectivity.

There is no ID pin, as that's only implemented on plugs. In USB C, the CC pins handle this, and pulling them to ground with a 5K resistor will initiate OTG mode.

It's the D+ and D- like normal. There is two of each because USB C is supposed reversible. You can insert the plug both ways and it will still be a valid USB 2 connection, as usb 2.0 does not negotiate the pinning. Flip the plug 180 degrees and the same pins will connect in the same order. Your board should connect both together for maximum connectivity.

There is no ID pin, as that's only implemented on plugs. In USB C, the CC pins handle this, and pulling them to ground with a 5K resistor will initiate OTG HOST mode on the other side of the link.

added 2 characters in body
Source Link
Passerby
  • 73.4k
  • 7
  • 95
  • 212

It's the D+ and D- like normal. There is two of each because USB C is supposed reversible. You can insert the plug both ways and it will still be a valid USB 2 connection, as usb 2.0 does not negotiate the pinning. Flip the plug 180 degrees and the same pins will connect in the same order. Your board should connect both together for maximum connectivity.

There is no ID pin, as that's only implemented on plugs. In USB C, the CC pin handlespins handle this, and pulling itthem to ground with a 5K resistor will initiate OTG mode.

It's the D+ and D- like normal. There is two of each because USB C is supposed reversible. You can insert the plug both ways and it will still be a valid USB 2 connection, as usb 2.0 does not negotiate the pinning. Flip the plug 180 degrees and the same pins will connect in the same order. Your board should connect both together for maximum connectivity.

There is no ID pin, as that's only implemented on plugs. In USB C, the CC pin handles this, and pulling it to ground with a 5K resistor will initiate OTG mode.

It's the D+ and D- like normal. There is two of each because USB C is supposed reversible. You can insert the plug both ways and it will still be a valid USB 2 connection, as usb 2.0 does not negotiate the pinning. Flip the plug 180 degrees and the same pins will connect in the same order. Your board should connect both together for maximum connectivity.

There is no ID pin, as that's only implemented on plugs. In USB C, the CC pins handle this, and pulling them to ground with a 5K resistor will initiate OTG mode.

added 99 characters in body
Source Link
Passerby
  • 73.4k
  • 7
  • 95
  • 212

It's the D+ and D- like normal. There is two of each because USB C is supposed reversible. You can insert the plug both ways and it will still be a valid USB 2 connection, as usb 2.0 does not negotiate the pinning. Flip the plug 180 degrees and the same pins will connect in the same order. Your board should connect both together for maximum connectivity.

There is no ID pin, as that's only implemented on OTG plugs. In USB C, the CC pin handles this, and pulling it to ground with a 5K resistor will initiate OTG mode.

It's the D+ and D- like normal. There is two of each because USB C is supposed reversible. You can insert the plug both ways and it will still be a valid USB 2 connection, as usb 2.0 does not negotiate the pinning. Flip the plug 180 degrees and the same pins will connect in the same order. Your board should connect both together for maximum connectivity.

There is no ID pin, as that's only implemented on OTG plugs.

It's the D+ and D- like normal. There is two of each because USB C is supposed reversible. You can insert the plug both ways and it will still be a valid USB 2 connection, as usb 2.0 does not negotiate the pinning. Flip the plug 180 degrees and the same pins will connect in the same order. Your board should connect both together for maximum connectivity.

There is no ID pin, as that's only implemented on plugs. In USB C, the CC pin handles this, and pulling it to ground with a 5K resistor will initiate OTG mode.

Source Link
Passerby
  • 73.4k
  • 7
  • 95
  • 212
Loading