# No output voltage on wiper when using pot as voltage divider

I've been trying to teach myself about potentiometers and how they can be used as voltage dividers. I bought some Alpha 10k linear pots to use in a really basic test circuit. I intended to connect the pot to my breadboard but unfortunately it doesn't fit so I've soldered some spare jumper wires to the pins of the pot.

In my circuit I have power from my Arduino Uno board (3.3v) connected to the leftmost pin on the pot and the other outer pin on the right is connected to ground. The middle pin (which I've assumed is the wiper) is connected to ground as well. When I measure the voltage between the two outer pins it's consistently about (3.2v) as I would expect but when I measure the output voltage between the wiper and ground it's either 0 or moves randomly between different values regardless of where I've turned the knob to. I'm wondering if I've misunderstood how the pot should be wired in this configuration or if it's just a case of bad soldering? • Here's your problem if you want a voltage divider: "The middle pin (which I've assumed is the wiper) is connected to ground as well." Jul 24 '16 at 13:58
• Ah ok. So if I just want to measure the output voltage what should I connect the wiper to? Thanks for taking the time to answer. Jul 24 '16 at 14:00
• Start with a new potentiometer, and connect the wiper only to the multimeter. Jul 25 '16 at 7:58

A potentiometer works in the same way as a simple two resistor potential divider, so here on the left is the equivalent of the schematic on the right showing a potentiometer. The middle output being the wiper of the potentiometer. On the physical potentiometer itself the middle pin is usually the wiper but I would recommend that you check that with a data sheet for the potentiometer.

I hope that this clears up the connections and just for extra knowledge here is a formula which will work to calculate the output voltage from the resistance of the two resistors either side of the output:

$$\mathrm{Voltage\space Out} = \mathrm{Voltage\space In} \times \left(\frac{R_2}{R_1+R_2}\right)$$ simulate this circuit – Schematic created using CircuitLab

• I've had a look for the data sheet but I'm not having much luck. Here is a link to the site I bought it from: maplin.co.uk/p/… If I was to connect a resistor between the wiper and ground would the output voltage appear across the resistor? Thanks everyone for their help so far. Jul 24 '16 at 14:22
• Okay, I have had a look but I also can't find one so the next best thing I can recommend is using a multimeter. If you have one I would measure the resistance of both of the outer pins relative to the central pin. If it changes when you twist the knob of the potentiometer relative to each other (the two values add up to 10k ohms) then the central pin would have to be the wiper. Jul 24 '16 at 14:30
• Ok I've just checked the middle pin against both of the outer pins and the value does change. I don't understand why there's no output voltage though. I've soldered and de-soldered 3 of the same pots like this and the results are the same each time. Jul 24 '16 at 14:40
• The chances of the pots being fault are pretty much 0%, so it must be something to do with the wiring of them within your circuit. Could you please insert a schematic of the rough circuit you are using into your question so that we can ensure it is correct! Jul 24 '16 at 14:43
• I've added a very rough schematic of the circuit to my original post. The 3.3 v is from my Arduino Uno board as described above and ground is also on the board. Jul 24 '16 at 15:05

The middle pin (which I've assumed is the wiper) is connected to ground as well. When I measure the voltage between the two outer pins it's consistently about (3.2v) as I would expect

And at that point, you will have damaged the potentiometer because when the wiper was physically close to the 3.3V end you would be shunting hundreds of mA through the carbon track and wiper and burning it.

when I measure the output voltage between the wiper and ground it's either 0 or moves randomly between different values regardless of where I've turned the knob to

Yes, that's what you might see when the wiper and or carbon track is damaged.

## Inside a potentiometer This is the anatomy of a typical potentiometer

The blue part has some fixed Length L such that the total resistance of this piece of metal is equal to 10 Kohms When you want to measure the resistance between A - B you are not taking the total length of the piece of metal inside this potentiometer, instead you are able to vary this length using the knob.

And according to the electrical resistance equation the resistance you are measuring is now a function of length L between A - B So, you should always use the wiper [Middle pin] to read the voltage with respect to the circuit reference voltage [GND]

If you want an equivalent circuit for your potentiometer. You can think of this circuit The total resistance between A - C is always 10Kohms but the one changing is the resistances between A - B and B - C