Verification of SCR Driving Circuit

Several years ago I attempted to build a coil gun, but gave up in frustration after burning out several SCR's when designing the trigger circuit. The SCR is used as the switch that dumps the energy stored in the capacitor into the coil.

I've since brushed up on my fundamentals and tackled the problem once more. Below is the circuit I've come up with.

V2 applies a 3.3V, 10ms pulse to the gate of M1. This pulls the gate of M2 low and causes current to flow into the gate of the SCR. Since V2 is a logic-level signal, I used this configuration so I could drive M2 without needing a level-shifter. R1

R3 is a current limiting resistor used to limit the gate drive current to 40mA, which is the rated maximum gate current required to turn on the SCR.

R4 is used as a pull-down resistor to prevent spurious signals from triggering the gate of the SCR.

Since C1 is charged to 200V, I've included D1 to prevent the drain of M2 from seeing large voltages when the SCR is triggered.

L1 is the coil and D2 is used as a flyback diode to prevent reverse charging of C1.

I know I've left out some details, but is the overall design of this circuit good practices?

• No, it's not even close to a working design, let alone good practices. Even added to your text, I'm still not even entirely sure what you had hoped to achieve. (Though I think you imagine it might be used to charge $C_1$ to a high voltage. But I'm not entirely sure of that, either.) It would, however, make an interesting artistic piece of work or something I might see as a secret gadget on some movie. – jonk Jan 8 '17 at 18:40
• What is the value of VCAP? – WhatRoughBeast Jan 8 '17 at 18:41
• @WhatRoughBeast Initially 200V – dgreenheck Jan 8 '17 at 19:01

The major problem appears to be that your SCR Cathode will start to rise as the device turns on and critically reduce the gate drive. You certainly won't meet the minimum t(gt) of 2 uS and may find the SCR turns on very slowly.
You should move the SCR to the ground side of the inductor.

Perhaps more like this:

simulate this circuit – Schematic created using CircuitLab

• Thank you! That works much better than what I had and lets me eliminate the diode in series with the gate of the SCR. – dgreenheck Jan 8 '17 at 20:24

I haven't scrutinized your triggering circuit and won't dwell on it as it may be somewhat secondary to your SCR burn out problem (the trigger circuit does seem unintuitive). You have not indicated the nature of and how the capacitor charging source V_CAP is connected. If V_CAP is a DC source with no zero crossings and remains connected to the capacitor when the SCR is fired, the SCR will remain in conduction once triggered, ultimately allowing a steady DC current to flow through the SCR and coil and likely destroying the SCR (essentially a short of the SCR). If V_CAP is isolated from the capacitor prior to triggering the SCR, then you should not suffer from SCR burnout (assuming that withstand voltages are respected).

As pointed out, the cathode of the SCR should be connected to ground potential. You can do this as suggested or you could arrange the circuit similar to a flash lamp circuit with the capacitor in series with the coil and V_CAP. The capacitor charging current path would be through the coil. At the point the capacitor is charged, V_CAP would be isolated from the capacitor and the + terminal of the capacitor would be connected to ground through a switch or SCR dumping the charged current into the coil. If V_CAP happens to be the unfiltered rectified output of something like an inverter circuit, the rectified waveform may eliminate the need to isolate the SCR to allow it to shut off and the capacitor to resume charging.

A resistor in series between V_CAP and the capacitor may be desirable to limit charging current to something reasonable.

I also don't think you need the recirculating diode D1. If the SCR was instead a power MOSFET and you were using the MOSFET to switch off the coil current, then you might need the recirculating diode.

• Thanks for your answer. C1 is charged and then disconnected from the charging circuit. As you pointed out, in the past I have made the mistake of leaving the charging source connected which resulted in burnout. D1 was included to mitigate the effects from improper placement of the SCR, so yes, I have removed that from my design now. – dgreenheck Jan 8 '17 at 21:09

A typo on my part. I meant D2, not D1.

I had a slight brain lapse. I was thinking triggered circuit where the capacitor dumps its energy into a circuit where the energy is dissipated (flash lamp or capacitor discharge ignition). Your circuit has no apparent resistive load so is theoretically a resonant undamped circuit. The resonance means that the current will cross through 0 so the SCR will attempt to cease conduction. Have a look at this discussion of a resonant LC circuit with an initial voltage on the capacitor:

Of course, there is no such thing as zero resistance. However. ignoring resistance, your peak sinusoidal current is 7.61xV_CAP (based upon 50 uH and 2900uF). If your V_CAP is 20 volts, your 'theoretical' rms current would be 107 amps. That might exceed the rms value of the SCR; but, probably not the non repetitive (single half cycle) surge current of the SCR since the current should extinguish at the first current 0 crossing. However, if the gate circuit remains high during this, it is not immediately obvious how this effective 1/2 wave circuit is going to operate. Modeling with SPICE might prove some insight: