I want to create a circuit that will power my Raspberry Pi using Lithium Polymer. My knowledge of LiPo is rather low and I believe they can get dangerous if used incorrectly so I turn here.

THe intention is to create a LiPo battery (of two cells) that I can charge with a LiPo charge circuit chip of suitable type, that part I'm ok with.

Then I hope to use something like the LM2676 3A switching regulator to get the 5V out that I require.

My main question is, do I need any sort of circuitry when running the LiPo cells for protection, for example to ensure they don't get discharged too much?

  • 3
    \$\begingroup\$ LI-PO batteries are prone to explosion if just about anything goes wrong. You overcharge them--They explode, you discharge them too rapidly--They explode, You drop them--They explode, you get them too hot--They explode, you look at them the wrong way--They explode \$\endgroup\$
    – Reid
    Aug 27, 2012 at 20:20

2 Answers 2


Protection circuitry is a highly critical element in a safely usable Lithium-polymer or Lithium-ion cell. Raw (unprotected) cells are less commonly sold, i.e. many times, the manufacturer of the battery includes protection circuitry as part of the battery; however, for safety, do not assume this is the case and check the datasheet of the battery.

Purpose of Li-ion/LiPo protection circuitry

The protection circuitry serves to protect against short-circuit, over-discharge, and over-charge conditions. Loosely speaking, the circuitry relies on an over-current cutoff, an under-voltage cutoff and an over-voltage cutoff respectively for ensuring against those three conditions. Sometimes, protection circuitry also includes thermistor-based overtemperature protection.

Unprotected versus Protected batteries

You MIGHT conceivably get by with an unprotected battery, for simplicity, if you have certain components on your PCB, e.g., a fuse (prevents overcurrent/short-circuit), an undervoltage-supervisor IC (prevents overdischarge), and a smart battery-charging IC (prevents overcharge).

But my personal assessment is: Unless you are able to constantly monitor the battery, do NOT use an unprotected battery; protection circuitries are fairly simple to implement (e.g. using pre-packaged protection ICs), or alternatively, a protection-added battery is easy to purchase.

How to implement Protection circuitry (for a Two-cell pack)

If you choose to implement it yourself (versus buying a protected pack), then here are two protection ICs you can consider for your scenario (i.e. two-cell Li-ion or LiPo):

  • \$\begingroup\$ @Hamid: Why are you using a two-cell configuration? Why not use a stepup regulator/boost-converter to 5V? \$\endgroup\$
    – boardbite
    Aug 28, 2012 at 7:54
  • \$\begingroup\$ Very good question, why aren't I? Do you recommend doing so, considering I need at least 1A typical out of it? I didn't think that kind of power would be feasable with a single cell. \$\endgroup\$
    – Hamid
    Aug 28, 2012 at 9:17
  • \$\begingroup\$ Actually, Li-ion/poly are usually rated for 2C discharge to my knowledge (thus 1000 mAh battery can handle 2 amps), however, depending on the integrated protection circuitry on board the battery, they may discharge only maximum of 1 amp discharge; even then you should be fine for your case. For example, this one seems to have a limit of 1 amp discharge: Sparkfun LiPo 1000mAh. As a bonus, it has protection on-board as the description states, so you should be good to go! \$\endgroup\$
    – boardbite
    Aug 28, 2012 at 9:28
  • \$\begingroup\$ Thanks, that makes sense, however, I was hoping to run it for a little longer than an hour :( lets say I did go for this, which has the protection circuitry on board, what circuitry can I therefore exclude from the electronics I build? I'll obviously need a charger IC (MAX1555 equiv)... \$\endgroup\$
    – Hamid
    Aug 28, 2012 at 9:30
  • \$\begingroup\$ Well, please read the Sparkfun description of that battery, and the datasheet, and you'll understand what's already on-board the battery, which is sufficient for most apps. But you might want to add a 2nd protection on PCB for undervoltage cutoff and a fuse. Charger IC: I recommend MCP73831T, which is used for example in this board). Boost converter that can handle 1A discharge -- play with the "Output current" filter on this search engine at Mouser. \$\endgroup\$
    – boardbite
    Aug 28, 2012 at 9:38

TE Connectivity Circuit Protection provides a host of information as it pertains to Lithium Polymer cells and how to provide the proper level of protection to help prevent against catastrophic events from occuring. I host a blog "Around the Circuit" and we just posted a short video from one of our design engineers where he talks about pack protection. I invite you to check this out at http://blog.circuitprotection.com/blognews/battery-cell-and-pack-protection-%e2%80%93-te-talks/[Battery Cell and Pack Protection][1]

It may be of some use to you as you try and resolve your protection problem.


Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.