Questions tagged [at-commands]

AT commands are used to control MODEMs, such as GSM/GPRS/bluetooth modules.

Filter by
Sorted by
Tagged with
0
votes
0answers
14 views

how to record microphon input in sim800l gsm module

I want to know if there is a way for the sim800l module to record the microphone input and then play it during the call? By this tutorial, I can upload a pre recorded 'amr' file on this module and ...
0
votes
1answer
20 views

Bluetooth HC-05 AT Commands

I'm attempting to put an HC-05 module into command mode in order to change the PIN and default baud rate etc. According to the datasheet, PIO11 needs to be high to do this, so I connect it to 3.3v, ...
12
votes
10answers
46k views

What AT command should be sent to modem to get time?

I am using SIM800E. I want to know what AT command should be sent to the modem to get time? This modem has a RTC. But I need to set it automatically through cell tower. The tower can send the time to ...
0
votes
1answer
35 views

What is single and multi connection mode( AT+CIPMUX=0 or 1) in esp8266 AT commands

I was studying the AT commands to program atmega328p for the communication with esp8266. Now I am confused with the command AT+CIPMUX=0 or 1 , it explains that 1 for multiple connection, 0 for single ...
0
votes
1answer
87 views

SIMCom SIM808 SD card problem

I am working with SIMCom's SIM808 2G+GPS modem and trying to connect it to an SD card. I am following SIMCom hardware design docs, to save some data in SD memory. The problem is: when I send ...
1
vote
3answers
5k views

How to call AT command on XBee from Arduino

I am trying to set the SM (sleep mode) register on the XBee radio. These registers can be set with so called AT Commands, listed from pg. 28 in the XBee/XBee Pro Product Manual. This can be done ...
1
vote
0answers
30 views

How do you get the call ringing response after sending ATD from gsm module?

I have a gsm module. I want to know which AT command can tell me if the target phone is ringing or not. I want to count time between start of ringing and user response Example: atd12345 ...
0
votes
1answer
5k views

How to interface GSM with 8051 microcontroller to send SMS?

I am doing a project on SMS sending through GSM using SIM 900 module and 8051. My code is: ...
5
votes
3answers
9k views

Trying to find location in GSM network

I am using a GSM modem by Simcom SIM 800E. I'm interfacing it over the serial link. I am passing command AT+CSCB to get the location. But I am not getting it. I ...
3
votes
2answers
13k views

Posting to php server using SIM900 GPRS with AT commands

I am using a SIMCOM SIM900 GSM/GPRS module in an embedded hardware application. Rather than sending device data to a server by SMS (what I've been doing so far) I want to switch and start using GPRS ...
0
votes
1answer
651 views

How to connect (pair) two CC41-A module

I bought two CC41-A BT modules. First I want to buy HM10 modules. I wonder if I can connect this two CC41-A to send and read data wirelessly. I look in datasheet but I cant find suitable AT command (I ...
1
vote
1answer
7k views

SIM800L not responding to AT commands

I am on a very exciting project, by the SIM800L module is resisting hard ! The hardware : clone arduino nano (dx.com) SIM800L module + antenna (dx.com) Lipo battery 3.7V 150mAh (letmeknow.com) The ...
0
votes
0answers
129 views

How does GSM Module store incoming SMS in its “SM” or “ME” memory?

I am using AI Thinker A7 GSM/GPRS/GPS Module demo v7.1.(The Rx, TX, GND pins of this module are connected to tx, rx, gnd pins of the prolific Rs232-TTL converter and a virtual com port is open in ...
3
votes
1answer
90 views

What are AT commands ? When to use them?

I read some articles about the AT commands but I am still unable to understand something. As the article says "AT commands are instructions used to control a modem." I used a while ago an Bluetooth ...
0
votes
0answers
612 views

Enabling SD card access on SIM808

I am currently working with SIMCom's SIM808 2G+GPS modem. In my setup, an MCU communicates with the modem over UART to save some data in the SIM808's filesystem. As the modem's built-in memory is < ...
1
vote
2answers
9k views

HC-05 Bluetooth AT+INQ command not working

I have followed the directions from the site below for bluetooth comm between an Arduino board using the HC-05 and an smartphone. It works fine. The problem is that I need to measure the RSSI from my ...
0
votes
1answer
105 views

How can I read/write bytes to SD card slot of MC60A?

I am working on a clickBoard with MC60 A GSM module from MikroEletronika company. This clickBoard has two slots: (1) one for SIM card and another (2) for micro SD cards. I have read all the available ...
0
votes
1answer
676 views

UART - Writing and reading AT commands

I am working with a B-L072Z-LRWAN1 board and a 8pya00-simcom-evb v1.02 board with SIM7000E. This SIM module operates through AT commands and I need to send these commands through an UART connected ...
0
votes
1answer
11k views

Correct AT Commands sequence for Quectel M95 GSM module

I have easily managed to connect the M95 GSM module to an Arduino and can communicate. I want to have a very basic way of posting data to a website from the Arduino. It seems the AT commands are ...
0
votes
3answers
2k views

SIM908 GPS STATUS “Location Unknown” Error

I'm using a SIM908 module on a custom board and am having trouble getting the GPS location from it. Everything else works on the module. I can send SMS, make calls and send and receive data from a ...
0
votes
1answer
789 views

SIM800L - No response while sending AT commands

I'm new to this arduino world. I'm trying to communicate with my arduino nano and SIM800L. I read few things in the internet and found a basic code. I tried copying it and tried to work it out, but I'...
2
votes
1answer
581 views

SIM808 registration denied for new SIMs

I have a SIMCom SIM808 2G GSM module on a custom PCB based upon the Adafruit FONA. I got a bunch of 2G SIM cards from Aeris.net. The problem is when I first put the SIM cards in my device, I get "...
3
votes
3answers
29k views

SIM900 Error on AT Command AT+SAPBR=1,1

I intend to send some information through GET method to a php page using the SIM900 module. I tried the following sequence of commands with success. ...
1
vote
1answer
109 views

how to send inter-operator sms via GSM/LTE module

I am using a GSM/LTE module (EC21 Quectel) to send and recieve sms with HyperTerminal application on computer by at-commands. I can send sms to devices with the same operator (intra-operator), but ...
0
votes
2answers
62 views

Force cellular modem to transmit at maximum power [duplicate]

I want to force my cellular modem to transmit at maximum power so that I can see if that is the cause of microSD card crashes that I have been experiencing in an embedded application. My modem is a ...
0
votes
2answers
183 views

SIM808 always returns the same temperature

I have a SIMCom SIM808 module built up on my own breakout board. Whenever I query the temperature I get back the exact same temperature, 24.11 (deg C) despite the actual temperature in the room ...
0
votes
1answer
1k views

Uncertainity with CIPSEND command to updating the data field on thingspeak using esp8266

I am having a bit of uncertainty here updating data on thingspeak using their generated API or may be because of the "AT+CIPSEND" command. Below are steps I followed for the 1st trial: ...
21
votes
5answers
8k views

Why do people use AT commands in serial communication?

I need to know why people in embedded systems use AT commands? When I have asked people say that it is a standard. So my question is: What does "AT" means? Why do people keep saying it's a standard?
0
votes
4answers
7k views

How to Make Sure SIM900 modem will always give me +PSSUTTZ string?

I am using SIM 900 modem to enable GSM connection wirh my product. Micro-controller Communicates with SIM900 modem through a SET AT commands over UART. My product is time critical and i need to have ...
1
vote
2answers
5k views

ESP8266 Wifi Module - prints “ready” but not responding to AT commands

Just received my first ESP8266 wifi module with some excitement. However I've been unable to fully communicate with it. I have connected the module to my computer via a usb to serial cable and I'm ...
0
votes
0answers
261 views

Problem in connecting to a server waiting for a TCP request using ESP8266

I'm using ESP8266 for connecting to a appspot-preview.l.google.com server which listens for TCP request and answers back a number (it's for training purposes). ...
0
votes
1answer
3k views

How do I send data over TCP from a SIM5320A?

NOTE: I have been using this as a reference. After recently purchasing a SIM5320A breakout board (the board) I have been trying to connect it to a TCP server. After having to connect the board to an ...
-1
votes
1answer
444 views

Cell broad cast messages command not working in SIM 800C

I am using SIMCom 800C module to get the location through cell broadcast messages. When I am executing command AT+CSCB=0,\"50\",\"0-9" , I get the response '...
1
vote
2answers
2k views

AT+CSQ without Disconnecting PPP Connection in ARCH Linux

I have a Telit GL865 GSM/GPRS module which is connected to a SBC (running ARCH Linux.) via Serial Port. For GPRS connection, PPP connection as indicaten on this page. I want to read Cell Tower Signal ...
0
votes
1answer
536 views

Issue of data posting in GSM over the GPRS from when use Different service provider

I'm using Telit's HE910 GSM Modem To Post The data on web-server. so i'm using different company service provider SIM Card to test the data posting from different service provider. In this case when i'...
2
votes
1answer
3k views

Sending Multiple Messages using Sim300 gsm/gprs module

I have interfaced SIM300 Gsm module with lpc2468 through UART. My main motive is to send SMS when some special sequence run. Now my requirement is that I should send the same messages to two numbers. ...
0
votes
2answers
282 views

Fetching network time from simcon 800c gsm module [closed]

Is there any way to fetch the current time from the 800c GSM module. I tried the following commands: AT+CENG=2 AT+CLTS=1 AT+CCLK? Output: ...
1
vote
2answers
3k views

Testing a connection to a TCP socket through SIM5320A cellular module

I'm using a SIMCOM 5320A module like this one to try to establish a TCP connection. I'm going through SIMCOM's application note on TCP/IP as a reference. The AT commands I'm using may very well be ...
0
votes
1answer
163 views

SIM900 SMS timestamps are not accurate enough

I'm experimenting a bit with a SIM900 module and a Raspberry Pi. I can communicate with it and receive/send SMS messages. However, there's a problem when a message that exceeds the 160 character limit ...
1
vote
1answer
1k views

AT-Commands: Send E-mail with attachment

I purchased a telit GSM Click (GL865) to use in my project. The architecture is composed of PIC based board with two MikroBUS connectors, I used one for the Telit GSM click, and the second one for the ...
1
vote
0answers
386 views

Error sending SMS to SIM900 in PIC

I am trying to interface SIM900 with PIC18F2520. I need to send SMS to a particular cell number. According to AT commands, ...
0
votes
1answer
863 views

GSM SIM-300 read msg problem

I'm unable to get a proper response from my GSM modem300, sometimes it responds with nothing, sometimes it replies half of line of ONE message from full inbox, sometimes it just sends the command (AT+...
2
votes
1answer
2k views

SIM800 - HTTP Get request time out

I've been working on a weather station project, and I used a SIM 900 module to upload the data to a web server. Recently I started using a SIM800-DS for the same purpose and I had to rewrite the code ...
0
votes
1answer
235 views

How to use hc-05 with pic32

I want to use Hc-05 bluetooth module with my pic32 controller for communicating with other bluetooth devices. I want to test the hc-05 module with my pic32 controller. I have made the hardware ...
14
votes
4answers
2k views

Why AT command set?

Frankly, Why do all communication ICs(or at least many of them or most famous or popular) such as Bluetooth or WIFI or GSM or etc support AT command set? why don't they have a simple pin for D/C(Data ...
0
votes
1answer
5k views

What does the GSM AT+CSQ command output signify?

So the command returns the received signal strength(RSSI) and bit error rate(BER). I see that the RSSI is obtained even if the SIM card is not inserted in the GSM module. So what does RSSI signify? ...
-1
votes
1answer
3k views

AT+CIPSEND problem with ESP8266

Here I am facing an issue with ESP8266 CLIENT Programming. The Problem is with AT+CIPSEND Command. This command is working for few times, but after few cycles, it waits too long for "SEND OK". I have ...
2
votes
6answers
14k views

HC-05 Bluetooth module not responding to certain commands

I've got a problem with my HC-05 BT module. I'm talking to it from my PC via USB/UART converter. When it's in slave mode I can link it with another device, send data using module's and converter's ...
3
votes
1answer
13k views

GSM Modem will not register to network

After getting two modems (dev boards) Siemens TC35 and SIM900A I cannot get them to send SMS. From the research it seems that somehow SIM cards will not register to network. I bought three SIM cards ...
11
votes
1answer
3k views

AT Commands to transmit data through TCP/IP stack with LTE network

I need to design an embedded sotfware that will drive a LTE cellular device (like u-Blox TOBY L2 Series) and its TCP/IP stack to transmit some data toward a distant server. I'm waiting for the device ...