# Questions tagged [band-pass]

Bandpass is an adjective that describes a type of filter or filtering process; it is to be distinguished from passband, which refers to the actual portion of affected spectrum. Hence, one might say "A dual bandpass filter has two passbands." A bandpass signal is a signal containing a band of frequencies not adjacent to zero frequency, such as a signal that comes out of a bandpass filter.

19 questions
238 views

### Filter-Amplifier circuit for Low Voltage I/P circuitry

I'm designing my first ever circuit for a hobby project. I've a sensor that outputs in mV (1 to 2) and a controller with ADC. The ADC is 16 bits, VDDA = 3.0 V, Temp = 25 °C, fADCK = 1.0 MHz. Since the ...
114 views

### Predicting decay time of a resonant bandpass filter?

In a typical resonant bandpass filter, resonance is set as none at 0 and full at 1, such that the filter rings infinitely at 1 and not at all at 0. If there is a two-pole resonant bandpass filter, ...
4k views

### The Cutoff frequency of bandpass filter

Given: Center Frequency f0 = 2.2KHz Q factor = 5 The problem I'm facing is this: How do I calculate the 2 cutoff frequencies of this band pass filter? I'm confused because my question says "The ...
303 views

### Designing 4th order Butterworth Multiple feedback bandpass filter

I'm trying to design a 4th order Butterworth bandpass filter using Multiple feedback topology. The design requirements I am trying to achieve for this filter are; Q factor = 10, Av = 11, fc = 100kHz ,...
69 views

### Grounding oscilloscope probe effects

I have built an active band-pass filter on a breadboard with the use of an MC33078p op amp. Gain is 32 on paper. When I apply the AC signal to the circuit, 18.1mV P-P and 660kHz, the oscilloscope ...
33 views

### Adjusting the gain on a 4th Order Butterworth Bandpass fIlter gain

I designed a bandpass filter with the TI filter designer tool but I initially designed with a gain of 40 dB. However, I'd like to reduce the gain to 20dB but I'm having issues doing trying to figure ...
76 views

### Easiest way to find transfer function of a lossless ladder filter after we finish design?

I have completed my Lossless Ladder BPF design, but I don't know how to find the transfer function of the resulting circuit without going through the slow and rigorous process of getting resistances ...
141 views

### First-order analog active bandpass filter with variable center frequency

I've thought about designing an active first-order bandpass filter with variable center frequency and fixed bandwidth, using OpAmps, as a project for an Applied Electronics class. My first try was to ...
92 views

### components used to make a butterworth filter

I doing some amateur radio experimentation and want to create a bandpass filter. I believe that a Butterworth filter would be good because it has a flat frequency response in the pass band. My center ...
433 views

### Center Frequency Shift Bandpass Filter

I have set Tow-Thomas filter to get bandpass output. I want center frequency to be precise as much as possible. If there occurse center frequency shift in the lab, what are possible way to compensate ...
396 views

### How to determine the RLC values for a bandstop filter

I've been looking through the vague online documentation for designing a basic bandstop filter. I have the two frequencies which I want to attenuate but I cant seem to find how to calculate the values ...
45 views

### Designing an audio amplifier, problems with bandpass filter

I am trying to build a Audio amplifier for a university project, I think that most of my circuit is done but I have an issue with my filter as my sine signal is not symmetrical after filtering to ...
68 views

### AC voltage through a capacitor

I've built a band pass filter to detect speed using a radar motion detector (IPM-165 http://nic.ath.cx/PDF/sensors/radar/CDM324-doppler/InnoSenT/InnoSenT_application_note_III_11_06.pdf). Using PSpice ...
40 views

### RC bandpass filter using two port network parameters?

So my assignment is about exploring two port networks and the use of the 4 parameters, now one of the tasks is to design a bandpass filter with cascaded high pass and low pass filters, now I am really ...
218 views

### whats the difference between a cascaded band pass filter and a normal band pass filter (Audio visualizer)

simulate this circuit – Schematic created using CircuitLab currently im building an audio visualizer i would like to know what is the difference between a cascaded 2nd order band pass filter ...
321 views

### LC band pass filter

I'm looking at implementing an LC bandpass filter, where I want upper and lower cut off frequencies to be 1254 Hz and 48 Hz respectively. Based on the pictures I've added - from http://www.radio-...
54 views

### How would one design a circuit to detect energy in the 3-140GHz ranges economically

We are looking to make something to detect RF frequencies in the SHF and EHF bands, from 3-140GHz, without requiring much frequency or amplitude accuracy. It would be ideally split into a few bands, ...