Questions tagged [bipolar-power-supply]
The bipolar-power-supply tag has no usage guidance.
18
questions
0
votes
0
answers
36
views
Grounding a bi polar high voltage pulser
This was a "brain teaser" in a circuits class, where only theory is required. Any equations or vocabulary to look into would be greatly appreciated. The question is the following:
You are ...
2
votes
4
answers
121
views
36VDC to +/-15V linear regulator setup - will this design work?
I designed a +/-15V power supply setup and trying to find/fix problems before running another PCB production run.
It will accept 36VDC (800mA) from an off the shelf part via a barrel connector. I ...
0
votes
0
answers
55
views
Boost converter with regulator
I have set up a boost converter with a regulator in LTspice, but I get a lower voltage at the output than at the input. What could be the reason?
1
vote
0
answers
26
views
Making a unipolar HVPS bipolar safely
I have a Keithley 5kV power supply (2290 model) that I use for high energy physics experiment. It has resolution of 1V and current resolution of 1uA. The range that it offers is +0V to +5000V via its ...
1
vote
1
answer
67
views
Standard approach for a split power supply ADC?
I'm currently working on a project that will incorporate an AD7124-8 ADC, which as far as I understand can accept true bipolar inputs when provided a split supply. I tried to dig around for an app ...
1
vote
1
answer
324
views
How do I calculate the maximum load on a center-tapped AC/AC transformer for a bi-polar linear power supply with full wave rectification?
I have a 24 VCT AC to AC step-down transformer, which has three wire leads on the secondary. I'll call the secondary leads X, Y, and C, where C is the center tap. With a DMM, the voltage between X and ...
0
votes
0
answers
92
views
Bridger rectifier producing non-equal voltages
I am making a bi-polar 12V power supply with a centre tapped (12-0-12) AC transformer. On inspecting the voltages after the bridge rectifier (KBU-4B), the negative side produces -26V and the positive ...
0
votes
0
answers
51
views
General Guidelines for Bipolar ADC Power Supply
I’m building an AC Power Meter using the ADS131E08 from Texas Instruments and am trying to find the best way to generate a 400mA +/-2.5V supply from a +5V source. The 5V source is the isolated DC-DC ...
0
votes
1
answer
54
views
Designing of a voltage to current converter schematic
Voltage is from a sensor (0 to 4 V), and load is within -100 nA and +100nA, where 0V should be converted to -100nA and 4V to +100nA.
Here is my last trial (picture below.)
I got the -100nA for 0V and +...
1
vote
1
answer
75
views
Troubleshoot a bipolar amplifier circuit
I am working on a project in which I am attempting to interface with an ILDA galvanometer from an arduino to move around a projected laser beam. I am following a guide linked here, particularly step ...
0
votes
2
answers
128
views
How to create bipolar power supplying from Powerbank 5V 3A
I have 2 ADS1299 analog to digital converters(https://datasheet.octopart.com/ADS1299IPAG-Texas-Instruments-datasheet-17020782.pdf). I need to give them bipolar mode supplying but I must use a ...
0
votes
3
answers
405
views
How to convert +5V power source to +/-5V power source
To supply op-amp 1, I need a power supply voltage of +2.5V and -2.5V. To supply op-amp 2, I need a power supply voltage of +4V and -1V. The outgoing signal from the op-amp stage will be fed into an ...
1
vote
1
answer
803
views
LM2576-ADJ bipolar power supply troubleshooting
I'm hoping to find some help here troubleshooting.
The circuit in question is a bipolar power supply that makes use of two LM2576-ADJ. The desired output voltage is +12v and -12v. I've breadboarded ...
0
votes
2
answers
249
views
Is there such thing as a Bipolar Wall-wart?
Looking for a UL approved device that gives +9V and -9V from the 120VAC wall.
I need the +/-9V to power a circuit and I don't want to make an extra PCB.
My alternative is to have two 9V wall warts but ...
1
vote
1
answer
234
views
Low Voltage, High Frequency, High Amperage Power Supply Design
For an ongoing project of studying magnetic properties of various metals we need to use a power supply which can generate 25 V peak to peak, frequency 50- 500 kHz, 5A (PP) current. Frequency would be ...
0
votes
1
answer
75
views
Decreasing output of a voltage doubler
I'm trying to build the following circuit. The advice on the site I got it from said to try using 1n4001's instead of 1n5817's, because that would get the voltage down to around 15V, which is what I ...
0
votes
0
answers
50
views
Generating high current negative supplies
I'm trying to generate a high current negative supply (30A, -2V). This is to be a negative symmetric supply along with a (30A, +2V) rail, with an actively driven ground which I need to be system ...
1
vote
1
answer
60
views
Using 2 postive regulators with 2 prong power supplies for bipolor power supply
My nephew and I have been working on a circuit that uses +/- 4.5V. Up until now we have been using 2 3-AAA battery holders to supply each leg and now wish to move to mains power.
My question is, ...