Questions tagged [buzzer]
A buzzer is an audio signaling device, usually piezo-electric.
39
questions
4
votes
5
answers
844
views
12V piezo buzzer not working using ESP32
I'm trying to make my buzzer sound when hooked up to 12V and a MOSFET in between but I'm perfectly failing. I'm using GPIO15 of my ESP32 WROOM to send a PWM signal to the MOSFET but nothing really ...
0
votes
1
answer
101
views
Control buzzer with GPIO
Edit: Realised Silly mistake, I have the emitter and collector swapped on my PCB :( sorry about that.
I'm trying to control a magnetic buzzer indicator using an STM32 MCU. I have the circuit below ...
- 105
0
votes
2
answers
58
views
Maximum voltage/current on a passive 8 ohm buzzer
I have a buzzer with:
8 ohm
1 watt rated power
Resonant frequency: 700/600 Hz
In order to make it sound, should I apply a PWM with 700/600 Hz, and turning ON and OFF?
What is the maximum voltage? ...
- 1
3
votes
0
answers
57
views
How to interface buzzer with LED in this circuit
Below is the circuit where I want to integrate the buzzer with the red LED.
The task is to add the buzzer, where the red LED is, in such a way that when the red LED (which is driven by the LED driver)...
- 31
1
vote
1
answer
107
views
Buzzer circuit sanity check
I am trying to establish if this buzzer circuit going to perform as expected
MPU: STM32 running at 3.3V, input will be coming from a GPIO pin that has a timer channel on it
Buzzer: A passive magnetic ...
- 147
1
vote
3
answers
612
views
How does the KLJ-5030 buzzer work?
I need a small package buzzer to replace the regular piezo buzzer which is too big for my design, so I tried the KLJ-5030.
I tested by applying 3V to positive pin and GND to negative pin and heard a ...
- 191
0
votes
1
answer
84
views
Add buzzer to multimeter
How can I add a buzzer to my EverStart Digital Multimeter 10711WDI circuit board, so that it buzzes when there is continuity?
- 1
1
vote
1
answer
44
views
Energy consumption after removing a part from a PCB
Does removing the buzzer chip from a PCB reduce the energy the PCB uses? Is it save to remove the buzzer?
It's an FMQ.
0
votes
1
answer
48
views
Buzzer with LEDs [closed]
Does anyone know a basic circuit so I can have a switch which activates a buzzer and a LED strip run off a battery?
- 3
0
votes
1
answer
230
views
Driving an active buzzer with an ESP32
I'm looking to drive an active magnetic 3V buzzer with an ESP32 pin through an N-Channel MOSFET as follows:
I'm not sure if the 100 Ohm resistor is needed and whether the value is correct. Buzzer ...
2
votes
1
answer
89
views
BPT intercom contacts [closed]
I live in a condominium. There is a door intercom system (see picture 1). The intercom is made by BPT company (Italy), model E/272 (see diagram in picture 2).
Since there is too much noise, I can't ...
- 21
0
votes
1
answer
113
views
Using a tilt sensor with NPN transistor
i'm making a fall prevent circuit and i want to make sure that this circuit is correct which i made
I would like to check because I don't have enough budget and time to buy many other parts
and this ...
- 67
0
votes
0
answers
55
views
LRA motor driver activity appears to be corrupting I2C commands to another device
I'm working on a device that uses an STM32L552ZET6Q, two DRV2605L motor drivers configured for LRA PWM output, and two BNO055 IMU units configured for IMUPLUS mode.
Each of the four chips is connected ...
- 329
1
vote
1
answer
351
views
Is this buzzer circuit correct?
Need to use an ESP32 to run a buzzer datasheet
The source current maximum per pin of the esp32 is 20mA
However I need to drive an active buzzer with 3V@30mA, so I decided to use an N-MOSFET (2N7002 ...
- 11
1
vote
3
answers
157
views
How to add buzzer in this circuit?
I'm making AC detector using bjt amplifier below is my circuit.
When it detects AC signal it will show result in LED and I want to add buzzer(3V) for show result in LED and buzzer ( 3V) so I ...
- 431
0
votes
1
answer
62
views
Proteus design buzzer quiz circuit
I am trying to design a 12-people buzzer quiz game.
I just want to use LEDs and AND and NOT gates, using one switch for reset.
The problem is that after designing it all the odd LEDs or even LEDs ...
- 13
1
vote
2
answers
228
views
Mechanical buzzer heard on AM radio
If I connect this little mechanical buzzer to a 3V supply, then hold my AM radio close to it with the radio tuned so I can't hear any stations, I can hear the buzzer on the radio. If I turn up the ...
- 669
0
votes
0
answers
297
views
How to remove Noise from the buzzer?
It is a simple water level indicator using BC547 and a buzzer. It works on a 9v/12v battery.
Its switch is placed beside the motor pump's switch. Whenever the motor switch is on there is a noise ...
- 1
0
votes
2
answers
165
views
Adding a buzzer to an existing LED
I have a set top box. It has a 3 mm green LED (on the front panel) that lights up when I connect the dish coax cable (signal LED).
I measured the voltage across the LED. It has 0 V when the dish cable ...
- 11
1
vote
1
answer
126
views
Want to create an alarm that senses 12 V and 240 V
On my boat I would like a warning buzzer to sound if the battery charger is on and the engine batteries are not isolated. Because if you start the engine with the battery charger on, the diodes in the ...
3
votes
3
answers
2k
views
Which flyback diode for magnetic buzzer
I am a novice, and I'm playing around with SMD magnetic buzzers. For instance, the CUI CMT-322-65-SMT-TR.
In the datasheet they recommend something like this:
After some Googling I learnt the diode ...
- 155
0
votes
1
answer
147
views
I need to make a circuit that activates an SOS buzzer, what are the components that I need? [closed]
I have a project in my college that requires me to make an SOS (... --- ...) buzzer without any IC's, what are the possible components that I can use for the delay between the morse code signals? ...
0
votes
1
answer
212
views
Would this circuit work for driving an internal buzzer?
A quick note, I had asked a similar question around driving an external buzzer previously: Driving external piezo buzzers
This is a question in regards to driving an internal buzzer, so not a ...
- 737
0
votes
2
answers
742
views
Driving external piezo buzzers
I am planning on using the following buzzer in my design (
SMACT-25-P15):
https://uk.rs-online.com/web/p/piezo-buzzer-components/8055272/
It says it requires external circuitry for operation.
I have ...
- 737
2
votes
1
answer
255
views
How large is a piezo buzzer's deformation?
For a standard run-of-the mill piezo buzzer (as in the image below), what order of magnitude would the deformation be (compared to 0V) that occurs when driving it within its normal operating ...
- 39
6
votes
3
answers
1k
views
Why is my infrared transmitter/receiver circuit not working?
I tried to make this circuit, but it didn't work like it should. I thought my connections were right but maybe it not.
This is the circuit diagram:
This is my layout. (I used other components as ...
- 87
1
vote
2
answers
611
views
How do I transfer this circuit to stripboard?
I want to construct this circuit because it look worth to try. However, I am not sure about connection between the components. This is the components placement that I tried, does it make sense?
Please ...
- 87
0
votes
1
answer
261
views
Connecting a bulb and a buzzer onto the same output of a relay
I am currently doing a project to light up a bulb and a buzzer at the same time. This circuit is an Arduino UNO which is connected to a relay to light up a bulb and the buzzer.
Can a 40 watt bulb and ...
1
vote
1
answer
223
views
How does this buzzer volume regulation work?
I've found a usage of a buzzer with volume regulation that I hadn't seen before.
Here's the schematic:
Timers PWM are activated like this (Atmel MCU) :
...
- 429
0
votes
2
answers
187
views
Purpose of the capacitor which is placed in parallel to collector and emitter of the transistor?
Can someone explain the purpose of the C469 capacitor, which placed in parallel to collector and emitter of the transistor?
Edit: Sorry for the mistake, C469 is parallel to CE
- 3
8
votes
2
answers
4k
views
How does the component "alarm boost three pin inductor" make a piezo buzzer louder?
I have a small circuit working on 2xAA batteries (3V) with an MCU and a buzzer for alarm sound.
I've already successfully used an active buzzer (with build-in driver oscillator) drived by an NPN ...
- 181
0
votes
2
answers
577
views
What makes an active buzzer oscillate?
All I can find online are descriptions on how active buzzers have an oscillator built in so that you just need to feed them a DC and they buzz at the frequency set by such oscillator, but I haven't ...
- 164
1
vote
1
answer
651
views
Where to put a buzzer so that it goes off when there is light (and should stop when there is dark)
I've successfully created (and breadboarded) this circuit:
simulate this circuit – Schematic created using CircuitLab
I cannot figure out where to put a buzzer so that it goes off when the LED ...
- 23
0
votes
1
answer
2k
views
Buzzer not buzzing in proteus 7.7v - used ic555
I am trying to simulate a mosquito repellent in Proteus v7.7. It uses an NE555 in astable mode.
My problem is that I cannot hear the buzzer buzzing.
I checked my circuit and everything seems correct ...
0
votes
1
answer
342
views
3.6 Vo-p rated buzzer on 5 V Arduino circuit
As a small buzzer to output simple audio, I am considering the
Jiangsu Huaneng Elec MLT-5020. Other buzzers of that size are also an
option, as long as their footprint isn’t much bigger than 5×5 mm.
...
- 1,301
0
votes
1
answer
91
views
No display at all tests, but shows continuity [closed]
My multimeter buzzer is ok and sounds when continuity is checked. However, no display on the LCD. Also, no numbers are showing in every tests voltage, resistance, etc.
I have replaced the battery and ...
- 11
3
votes
2
answers
467
views
Driving a tiny speaker via pwm, amplified with a BJT - in reverse?
I'm playing around with a micro and a small buzzer (passive). I built up an simple emitter-follower buffer to reduce the load on my uC, but I accidentally installed the transistor backwards on the ...
- 115
-2
votes
1
answer
2k
views
How to simulate Magnetic Transducer Buzzer (SMT8585-03H03LF) in LTspice- any model available?
I am adding a Magnetic buzzer into the design.
Buzzer part number is SMT8585-03H03LF from Bestar electronics.
Below are the specifications for quick glance.
Is it possible to get a LTspice model for ...
- 1,388
0
votes
4
answers
605
views
How to turn on a 12 V buzzer when transistor is OFF in the given circuit using minimal components?
In the given circuit I need to add alarm circuitry where the 12 V buzzer is ON when the relay/transistor is OFF.
Please guide me on how to connect the 12 V buzzer with minimal additional components.
- 103