Questions tagged [compensation]
For questions about designing electronics to account for undesirable characteristics or behaviors, such as frequency compensation in a feedback control system to avoid instability and/or improve gain and phase margin, reduce overshoot and ringing, improve bandwidth, etc. Consider using in conjunction with associated tags such as "feedback", "stability", "frequency-response", "nyquist-plot", "bode-plot", "operational-amplifier", etc., if appropriate.
15 questions
1
vote
3
answers
834
views
Problem stabilizing this PMOS LDO
I am considering a discrete LDO for a supply rail that needs ~\$m\Omega\$ impedance at 10 kHz.
While the following circuit does what I need (according to Spice), it becomes unstable if C2 is smaller ...
- 23.4k
2
votes
1
answer
1k
views
TL494 compensation
I am trying to make a homebrew power supply. It works at the moment, but compensation is not done yet.
Can someone help me to calculate and select the right poles and zeros? VCM is at error op-amp 1, ...
- 135
7
votes
2
answers
2k
views
Understanding in-loop compensation for capacitive-loaded OpAmp
I'm trying to understand the in-loop compensation for a simple amplifier loaded with a capacitive load, as seen in this article from Analog:
http://www.analog.com/library/analogdialogue/archives/38-...
- 133
2
votes
3
answers
7k
views
Intuitive way to see pole/zero directly from schematic
The image below is the electrical configuration and the transfer function of a type II compensator using OTA.
By looking at the transfer function, we can easily see that the circuit has two poles (...
- 1,661
6
votes
1
answer
1k
views
Loop compensation design of buck converter
I am trying to design loop compensation with type-3 error amplifier for a buck converter. I'm a student and very inexperienced in this subject. Please bear with me.
Here is the general procedure ...
- 897
5
votes
2
answers
810
views
Flyback power supply instability issue
I have created a switching power supply:
Input: 230 V AC
Output: 12 V DC, 1 A
Controller: UC3844
Topology: flyback
Switching frequency: ~ 100 kHz
Schematic:
When I start this power supply, output ...
- 5,528
2
votes
2
answers
246
views
14-Volt 6-Amp Power Supply Stability
Design Requirements:
The purpose is a linear DC power supply for 12-volt aircraft, marine, and amateur radio equipment
power source 20 volts @ +/-10%. (output 85W = 6A*14.2V)
Rser on V1 = 0.4 or ...
- 1,158
2
votes
0
answers
187
views
AC analysis of SMPS shows instability. How to modify the analysis to reflect the transient stability?
Background
I have designed a switch-mode power stage with voltage-mode control that uses an LCLC filter in its output to obtain a very low ripple output voltage.
I have empirically arrived at a ...
- 23.4k
2
votes
0
answers
606
views
Trying to perform transient frequency response with LTspice or Microcap, TL494 compensation
I have tried to do Bode plot of my uncompensated plant by myself in LTspice 17.1, but the result looks strange to me. This topic is a follow-on to this one.. I have no clue why it comes with 290 ...
- 135
2
votes
1
answer
2k
views
Do lead and lag filters have the behavior of high and low pass filters even if the zero and pole used are complex?
Consider the compensation transfer function \$\frac{s+z}{s+p}\$ so that the inequalities \$0<z<p\$ and \$0<p<z\$ correspond to lead and lag compensation respectively.
At very low ...
- 265
1
vote
1
answer
695
views
Analog implementation of imaginary roots in a transfer function
I have a simple boost converter, and from multiple papers I've read through, a Type 3 Compensator is recommended. I designed one in Matlab/Simulink, and it reacts very quickly. The problem is, when I ...
- 311
0
votes
2
answers
547
views
Op-Amp Input Bias Compensation for Multiple Feedback Filter
I'm adding an input bias current compensation network to the positive op-amp input of my band-pass multiple-feedback filter.
I'm setting the source impedance for the positive input pin equal to that ...
0
votes
1
answer
716
views
DC-DC converter error amplifier output
I am new to DC-DC converter electronics. I was wondering what the output of the error amplifier/compensator looks like.
Is the output of the compensator being driven to the Vref value set on the non-...
- 101
0
votes
1
answer
347
views
Poles and Zeros of a Transfer Function
I am trying to understand the physical meaning of poles and zeros of a transfer function. Can someone help me how to understand the Figure 2b in the link below?
What does the height of the cone ...
user220456
0
votes
0
answers
206
views
4-20mA current loop - transmit sensor reading
I am working on design loop current transmitter- to transmit reading value from thermocouple sensor using below design. I measured co-junction temperature using NTC instead of RTD.
During applying ...
- 61