Questions tagged [data-rate]

The tag has no usage guidance.

Filter by
Sorted by
Tagged with
13
votes
9answers
4k views

Why doesn't higher frequency mean higher data rate?

My question is very primitive :) I've read multiple articles today and answers here, on Stack Exchange, but still don't understand one thing. Why doesn't frequency itself affect data rate in mobile ...
0
votes
1answer
39 views

What is the meaning of Output data rate of Bosch BMI270?

what is the meaning of ODR (output data rate) BMI270 says it has 1.6kHz for accelerometer ODR does it mean internal registers update rate is 1.6kHz or 1.6kHz/(16bit x 3) = 33Hz ? (here 3 is, 3 ...
2
votes
1answer
52 views

what is the meaning of BLE data rate 1Mbps?

I am using BLE HM10 module which is BLE 4.0 1Mbps assume I have 1000000 data bits to send within a second, so I need 1Mbps bandwidth, Is 1Mbps only for Data bits? or 1Mbps means complete ...
2
votes
2answers
68 views

What is the meaning of Angular Velocity Vector 100Hz of BNO055?

I am using an Arduino Nano with BNO055 Adafruit library. The I2C speed is 400 kHz. The Adafruit BNO055 Absolute Orientation Sensor mentions Angular Velocity Vector (100 Hz). What does this 100 Hz ...
1
vote
1answer
43 views

How does i2c standard or fast mode effect the output data rate of the sensor?

I am using BNO055 motion sensor supports standard mode 100kHz and fast mode 400kHz but sensor specifies following Gravity Vector 100Hz Euler Vector, 100Hz Quaternion, 100Hz Magnetic Field ...
0
votes
0answers
96 views

Precise sampling rate for data acquisition with Arduino and Python

I built a simple data logger with Arduino and Python (Accelerometer --SPI--> ESP32 --USBSerial--> RPi). I used the timer interrupt to control the output data rate, which is set to 300Hz. But I noticed ...
37
votes
9answers
10k views

Why is wired Ethernet losing its speed advantage over wireless?

This has been bugging me for a while now. I did a couple wireless transmission courses back in my university days and it's a known fact that wireless transmission is hard. Partly because it's a shared ...
-1
votes
2answers
122 views

Calculate the data speed with clock rate

If the clock speed is 45.25MHz and I need 7 data cycles within that clock cycle, could someone show me the math to figure out the data speed frequency ?
0
votes
2answers
51 views

How to calculate the maximum data rate or frequency of a bus driver

I'm searching a suitable bus driver for a project. I found the Nexperia 74VHC244D. On the website they say the maximum frequency is 60MHz (here). But how do I calculate the 60MHz? Because it's not ...
1
vote
2answers
37 views

Bandwidth and Data Rate FSK Demodulations

I have a question about the data-rate limitations imposed from bandwidth for FSK signals. Suppose I transmit an FSK signal with frequencies as: $$f_1 = 2400 MHz,$$ and $$f_2 = 2401 MHz$$ that is ...
0
votes
1answer
246 views

What are the advantages of a wider bus in comparison to those of a higher clock frequency? [closed]

The aim is to increase data transfer rate. I understand each may have some drawbacks and advantages. Frankly I'm not knowledgeable enough to know of many so I'd like some input from others. I know ...
0
votes
1answer
54 views

IEEE 802.11b bandwidth and data rates

I am self-studying on how 802.11b bandwidth and data rates are calculated, primarily those of 1 and 2 Mbps. These are my understandings, please correct them if they are wrong. Please keep in mind I am ...
4
votes
1answer
495 views

Observing ethernet auto-negotiation packets using oscilloscope

In an answer to one of my previous posts seen here: Verifying 802.3 auto negotiation, @Zac67 mentions that by using an oscilloscope I could observe normal and fast link pulses that are sent in order ...
0
votes
1answer
114 views

Compatibility between XBEE-PRO 900 HP and XBEE SX

I wanted to use a 900 MHz xbee and I need one side to be surface mount. So I'm thinking of getting an XBEE PRO 900 HP (XBP9B-DMST-002) and an XBEE SX (XB9X-DMUS-001). These devices have the same ...
3
votes
2answers
438 views

what relationships exists between the BER vs SNR graphs of QPSK and QAM modulation schemes on data throughput. which scheme does better?

Using QAM and QPSK modulation schemes, RF field measurements like received signal power and pathloss were obtained from where the SNR values were estimated. Their BER values were also calculated and ...
3
votes
1answer
202 views

TX Antenna dBi relevant for transmit and receive rate?

If for example I have a USB WiFi adapter with -70dBm sensitivity and 20dBm tx output power and a 5 dBi omnidirectional antenna. If I change the antenna to 9 dBi, in the coverage zone with same range, ...
1
vote
2answers
11k views

sampling rate, data rate and bandwidth

I'm new to digital communication. How are the terms data rate and sampling rate related to the term "bandwidth" . Am I missing something here?.Can someone explain me in detail? thanks in advance, ...
5
votes
2answers
6k views

Does Nyquist rate depend on the sampling rate?

The book Computer Networks by Andrew S Tanenbaum mentions the following (paraphrased): For a noiseless channel, Nyquist theorem states: Maximum data rate = \$2H \space log_{2} V \$ bits/sec ...