Skip to main content

Questions tagged [delta]

The tag has no usage guidance.

Filter by
Sorted by
Tagged with
0 votes
1 answer
38 views

Star delta connection blower motor

I have a star delta motor connection. I just want to confirm if the current from the motor going to the overload and contactor is the same as the contactor going to the breaker? Because the reading I ...
hisyam husseini's user avatar
0 votes
0 answers
45 views

Delta to delta or delta to wye transformer

I am going to feed 240Vac 1-phase into a rotary phase converter the resulting 240 3-phase needs to power two robot controllers, but the controllers require 200-230Vac 3-phase or 400 - 480Vac 3 phase. ...
JCoder's user avatar
  • 11
2 votes
2 answers
371 views

Delta star, beginner question

Hi, can someone tall me why the line comes from behind the motor and comes back in front of it. Is it because internal connection is crossed? for example, u->x v-y w->z. What am I missing?
user1923363's user avatar
3 votes
2 answers
181 views

Do corner-grounded deltas exist outside of USA?

Do corner-grounded deltas exist outside of USA? If yes, where? Where do you find information about this? Is there an IEC standard that dictates which transformers exist where?
user1047455's user avatar
0 votes
1 answer
237 views

Three Phase Transformer Design

I design single phase transformers, around 400W - 8000W, but now im lost because i have to design a three phase transformer ( delta - delta connection ). I searched, trying to find a page that can ...
samuel mattio's user avatar
1 vote
1 answer
239 views

Explanation of 4-wire Delta Transformer Phasor Diagram

I have been studying some of the Tx configurations for metering. I've been looking at a booklet called the Power Measurements Handbook, which is sort of an informal resource in the metering world. I ...
compto2017's user avatar
2 votes
1 answer
110 views

Derivative of a waveform

I am self studying linear circuits and I came to a very basic problem. The problem: $$y(t) = e^{-t} u(t)$$ where \$u(t)\$ is the step function. Calculate the derivative of \$y(t)^{\prime}\$. My take ...
Homer Jay Simpson's user avatar
6 votes
2 answers
4k views

Three-phase motor Delta/YY connection diagram and windings troubleshooting

I am trying to troubleshoot this 1.4 kW three-phase motor and I'm unsure how its internal windings are interconnected or whether they are shorted. On the plate it says "Delta/YY 400 V", and ...
Robert Lee's user avatar
-1 votes
1 answer
179 views

Need to convert 240vDC to 3-phase "high leg delta": can an inverter be avoided? [closed]

I want / need to take a 3kW, nominally 240vdc say again DC and obtain "3-phase, high-leg delta (aka wild-leg delta) from it. (I won't answer questions on why, but if I feel the need later, I'll ...
Richard T's user avatar
  • 457
4 votes
0 answers
289 views

Zero current assumption in star - delta transformations derivations

The formula used for star delta transformations are: $$ R_A = \frac{R_{AB} R_{AC}}{R_{AB}+R_{AC}+R_{BC}} $$ and $$ R_{AB} = \frac{R_AR_B + R_AR_C + R_BR_C}{R_C} $$ The normal way that these formulae ...
Balu's user avatar
  • 43
11 votes
4 answers
980 views

Can I drive a 3-wire-delta-input appliance with a wye-output transformer?

We have a high-current industrial machine rated for 3-phase at 230 V; the nameplate literally says "PHASES: 3Ph + PE", "VOLTAGE: 3X230VAC", and "FULL LOAD: 92A". There ...
bernz's user avatar
  • 213
0 votes
1 answer
247 views

Is the Y connection advantageous for power supply?

I have heard that 'Y' connection is advantageous for the three phase supply and '∆' for the three phase load e.g. a motor. Please tell me if this is correct and if so why.
wooyoung kim's user avatar
-1 votes
1 answer
2k views

Why this motor shows delta 220 / star 380 which is usually the other way round from what I know? [closed]

Brand new induction motor arrived in the factory,it comes with gearbox on top controlled by VFD, but I could not understand it's nameplate, it should have shown just delta / star without voltage ...
user295305's user avatar
2 votes
1 answer
229 views

Why is one current reading ~20% higher than the other two in a balanced high-leg delta load?

We are using eGuage watthourmeters to monitor the outdoor unit on five VRF systems powered by two different 3P4W 120/208V high-leg delta panels. The neutral is not connected to the outdoor units. We ...
LShaver's user avatar
  • 881
1 vote
1 answer
213 views

Relation between line voltage and phase voltage in delta configuration

I have read answers pertaining to this same question, but I could not understanf why the phase voltage is equal to line voltage. This answer says: In a delta system, the two points required to ...
Darlington's user avatar
7 votes
2 answers
2k views

Understanding the total impedance in a delta connection

I'm trying to upskill by teaching myself electrical engineering. I already have a degree in theoretical physics and pure mathematics so I don't mind math-heavy answers. While I don't find the maths ...
hoff's user avatar
  • 81
1 vote
1 answer
359 views

In delta motors, the power factor angle refers to the phase current or line current?

A 600V, 60Hz, ∆-connected, 8-pole synchronous motor has a synchronous reactance of 0.15Ω and armature resistance of 0.02Ω. This motor has an output power rating of 46 hp with a 0.90 lagging power ...
OMAR's user avatar
  • 883
-3 votes
2 answers
292 views

Multisim delta-delta connection

I try to simulate a delta-delta transformer connection in Multisim but I get an error, why, I don't know. My diagram is as below: Here are the errors:
Wtow's user avatar
  • 3
0 votes
2 answers
604 views

Difference between "Rated voltage" and "Max. switching voltage" in relay datasheet

I'm looking for PCB EM-relay for switching 25A 380V load, and there is a lack of models on the market. I have find one of them. The T9G relay has MSV = 480V, but rated voltage = 277V. Also in header ...
segar's user avatar
  • 33
1 vote
1 answer
281 views

Single phase motor starting from high leg voltage

Typically stinger voltage is said to be nonuseable, the 208V between a high leg and a bastard tap. High-leg-delta configuration (Wikipedia). But since single phase motors require a phase offset to ...
Andrew Graham's user avatar
1 vote
1 answer
536 views

Solving for phase currents given line currents and line voltages in 3 phase unbalanced delta load

I am given the line currents and the line voltages for an unbalanced 3-phase delta connected load but need to solve for the phase currents on the legs of the delta load. I know that: $$I_{L1} = I_{a} ...
gmartine242's user avatar
0 votes
1 answer
1k views

In a delta wound 3-phase motor, how are the phase and line voltages equal?

After researching the 3 phase delta configuration, I'm confused as to how these three line-to-line and phase relationships can all be true. I have found the voltage/current relationships here , and ...
Lukaku's user avatar
  • 1
1 vote
1 answer
1k views

How to solve this star delta problem?

Please help me solve this star delta problem: My attempt: What to do next to solve this completely?
Shivam Jaiswal's user avatar
0 votes
0 answers
206 views

Problem figuring star delta starter circuit

I know the basic functioning of star delta motor starter configuration but kind of stuck on my current project which uses old L&T starter panel. I can't figure out the terminals like A1, A2 (coil ...
Rishabh's user avatar
  • 153
0 votes
0 answers
51 views

Open-Delta 3-phase transformer kVA rating

I have a V-V three-phase transformer supplying a 50kVA balanced three-phase load. I know that the apparent power of a three-phase transformer \$S_{3\phi} = 3VI^*\$ and that of an open-delta system is \...
Hector's user avatar
  • 403
0 votes
1 answer
1k views

Only 3 wires in 3 phase motor terminal box

I have a 3 phase motor with the nameplate below At the terminal box you have your standard 6 pins labelled u, v, w, u1, v1, w1. However, the u1, v1, w1 is not connected on the terminal block but ...
Luqmaan's user avatar
  • 55
0 votes
2 answers
756 views

3 pole SSR with Neutral connection

I am designing a heater block using 12 heaters. Each one has 200W/230V ratings. I have decided to use 3 pole SSR for control heaters with help of PID temperature controller. The SSR manufacture ...
user_fs10's user avatar
  • 871
0 votes
1 answer
786 views

Why delta connections are done when the motor is required to be operated at 220V?

I am working with a tip dresser which is used for dressing the tip of the welding gun. A motor is used in that tip dresser which is used to rotate the cutter to dress the tip. There are two provisions ...
ltpriyank's user avatar
0 votes
3 answers
876 views

Star Delta Starter control with Arduino

I don't have any experience with star delta starters but on doing some research I concluded that 2 push buttons (NO and NC) are required to turn on or off the system. I have a pump which is star delta ...
Rishabh's user avatar
  • 153
2 votes
2 answers
1k views

Delta-Star Combination Exercise

This post is regarding exersise 4-8 from the following book: Hughes Electrical And Electronics Technology 10th Ed. Here it is: Let's focus on what I tried for solving part (b) : Since this is an ...
Stamatis's user avatar
  • 135
1 vote
1 answer
334 views

Current in delta connection

I know how to calculate current in delta connection but just for knowledge purpose I wanted to know from basics why this method(in image) of calculating phase and line current is completely wrong ...
user215805's user avatar
  • 1,184
2 votes
2 answers
3k views

Motors Delta/Star connections to VFD

I've selected 230/400V motors (delta/star) and corresponding 400V VFDs for pump motors. Now I've been asked why I haven't selected 400/690V motors (delta/star), that are the standard and usually ...
Yoda Master's user avatar
1 vote
1 answer
97 views

What is the correct way to solve this problem?

I first solved it by converting the two star connected networks into delta networks and further solving them. Then I solved by considering one star, converted that to delta and then used parallel ...
Chandradhar Rao's user avatar
0 votes
2 answers
315 views

Calculating Phase wise Energy in Three Phase System

In three phase three wire system, is it necessary to calculate phase wise energy? As per my knowledge, in three phase three wire system we are concerned about only total power/energy. But does it ...
neeteen09's user avatar
1 vote
0 answers
124 views

4Wire 120/208 High leg delta - 320v to ground, 420v to C phase?

I have a 120/208 High leg delta service 4 Wire. 208v/120v/120v The reason for the call is main breaker failed. I get there and the 1 bus bar is not being powered by the main but the other 2 are. ...
rustymetal's user avatar
0 votes
1 answer
351 views

Star to delta transformation circuit

Is it possible to use star-to-delta transformation on this specific circuit below? If it is possible, can someone give me a hint on how to do it? I tried to do delta-to-star transformation and got the ...
user10995546's user avatar
1 vote
1 answer
2k views

Charger Delta Electronics ESR-48/40A E Voltage and Current Adjustments

Does anybody know how to change (i.e. program) the output voltage and limit the output current in the Delta Electronics ESR-48/40AE charger? The following web pages: this one and the next one have ...
Glaukon's user avatar
  • 111
0 votes
4 answers
19k views

Three-phase motor connection, 230 V delta or 400 V star?

I have a motor with these specifications: star 400 V delta 230 V The motor is of course 3-phase. How can I connect the motor using a delta connection if I have only 400 V line-to-line voltage? Where ...
Igor Okorn's user avatar
0 votes
1 answer
94 views

Delta to delta 2000 kVA transformer

I have a delta to delta 2000 kVA transformer that on power up with no load except whatever is in the main switch gear I am getting 400 volts to ground on one phase 280 on another and 95 on another, ...
Tim Poag's user avatar
0 votes
1 answer
41 views

Loading one line from Three Phase Power Delta Configuration

I have been trying to determine whether or not I can run one line from 3-phase power into a power conditioner that requires single-phase input. The current draw on this line would be around 10 A. ...
aniforatos's user avatar
2 votes
1 answer
13k views

Why don't the currents clash in a 3 phase delta connection?

Consider 3 windings, a, b and c. L1 is connected to A, L2 to B and L3 to C. The 3 windings are then connected in delta. If we could freeze frame the voltage waveform where L1 and L2 are positive ...
Ph3ng's user avatar
  • 347
0 votes
2 answers
629 views

Where does the sum current of the three currents flow?

In the following star and delta connections, if each individual current enters via Phases R, Y and B, where does the sum of the three currents (that is Ia+Ib+Ic) flow after meeting at the common point ...
penguin99's user avatar
  • 859
0 votes
1 answer
2k views

what will happen if the motor that is designed for delta connected in star connection

I have a motor which is designed for 3 phase, 380V. The power rating of motor is 132kw and motor stator winding is connected in delta connection. If I connect the same motor stator winding in star ...
Harshit goyal's user avatar
0 votes
1 answer
49 views

AD7173-8 gain register default value

In the AD7173-8 ADC, the default gain value is said to depend on the IC type. In the datasheet, the value is mentioned as 0x5XXXX0. But I couldn't find the exact value in the datasheet anywhere. ...
Tharaka Ratnayake's user avatar
0 votes
1 answer
242 views

How to implement a dirac delta as input signal for this system

y[n] = b0x[n] +b1x[n-1] I have this MA filter in matlab as following ...
Adam's user avatar
  • 101
1 vote
2 answers
4k views

How is Line and Phase Voltage the same for a Delta connected system?

I am having a little bit of confusion for some reason understanding how the phase and line voltage can be the same for a delta connected system, i understand why the current is different for the phase ...
Student's user avatar
  • 495
2 votes
2 answers
7k views

3 phase motor running on single phase using steinmetz delta connection

How do 3 phase motors manage to run on single phase power using the Steinmetz delta connection with a single capacitor? I thought capacitors only shift the phase angle upto 90 degrees, whereas 120 ...
Amit Hasan Arpon's user avatar
0 votes
1 answer
118 views

how to get the line voltage of 3 phase delta circuit with power factor known at first?

In the following picture, it shows that a black box at right. the circuit inside the black box is a 3 phase load balanced delta connection circuit. the line voltage of it is 500V and the power factor ...
Ezra Ma's user avatar
0 votes
1 answer
179 views

Fourier transform of a sum of 2 delta function

i have a channel impulse response \$h(\tau,t)=\delta(\tau-1/4t)+b\delta(\tau-T)\$ if I would like to take Fourier transform, I can take FT for each delta function and then sum up a result. \$FT(h(\...
user avatar
0 votes
1 answer
73 views

"3 phase" Type of winding I am not aware of, help? not wye or delta, maybe eFed up generator?

I bought a few 30 watt 3 phase motor/generators in supposedly delta configuration from a ali express. the motor did have only 3 wires coming out, plus the manual stating it, I am pretty sure this was ...
Robert Dold's user avatar