Questions tagged [deserialiser]
The deserialiser tag has no usage guidance.
13
questions
0
votes
0
answers
194
views
ISERDESE3 vs ISERDESE2 simulation
I am trying to simulate ISERDESE3 and ISERDESE2 modules.
It was quite easy for me to understand the ISERDESE3 configuration and compare the input and output. ISERDESE2, on the other hand, has a lot of ...
1
vote
2
answers
37
views
Voltage on the Serial Link and Parallel Resistor Value
This question is related to the previous question that I had over here
I found the serializer that I am using. It is over here
From the above serializer datasheet, on page 9, I found that the maximum ...
2
votes
1
answer
58
views
Voltage on the serial link
I am using this MAX9278 deserializer.
The inputs to the IN+, IN- pins of the deserializer are twisted pair inputs.
On the IN+ and IN- serial link, I have 2 AC coupling capacitors of 220nF 50V on each ...
0
votes
1
answer
25
views
GMSL Deserializer to LCD Link Rate
I need to calculate the Link Rate for my GMSL Deserializer which is connected to a 800 * 480 TFT Display.
In that case, I stumbled upon this Article
On the last few lines, they are asking to multiply ...
0
votes
0
answers
26
views
Deserializer Datarate calculation
I am having this MAX9278 deserializer IC.
The input to the pins +IN and -IN is a twisted pair input and therefore, it is a differential signal. I have configured the CX/TP pin to low since it is a ...
0
votes
0
answers
42
views
Coax or STP input to the Deserializer
I have this MAX9278 deserializer.
I am planning to give Shielded Twisted Pair (STP) input to the IN+ and IN- pins of the deserializer instead of COAX input.
Can someone help me to let me know what ...
0
votes
1
answer
28
views
Setting the address of Deserializer
I have this MAX9278 GMSL1 Deserializer.
I have 3 below questions:
How to configure the CX/TP pin if I want to use the coax mode?
And how to arrive at the address of the deserializer if I connect ...
0
votes
0
answers
32
views
SPI Configuration in TFT
I have a TFT which requires SPI Communication interface to get it configured.
My questions :
When we say, "configure the tft", what do we actually do? Do we set some bits or erase some bits ...
0
votes
1
answer
60
views
What is the meaning of Change in Output Offset Voltage between complementary output states
I have MAX9278 deserializer IC which is connected to a 3.1inch TFT display 800 (W) * 480 (H).
Deserializer provides 4 LVDS lanes and 1 clock to the display.
While I checking the electrical voltage ...
0
votes
1
answer
31
views
What are the main parameters to check display with display controller
I have MAX9278 deserializer IC which is connected to a 3.1inch TFT display 800 (W) * 480 (H).
Deserializer provides 4 LVDS lanes and 1 clock to the display.
What are the major parameters that I need ...
0
votes
0
answers
55
views
How to provide 3 options (pull-up, pull down and Open) in an IC
I have MAX9278 Deserializer IC.
I have 2 doubts.
Doubts :
I am performing the schematic now. Below, I need to provide options for both 24-bit, 27-bit and 32-bit.
How to provide the provision for all ...
2
votes
1
answer
218
views
SDLC Frame Check Sequence details
In the Synchronous Data Link Control (SDLC) protocol, the frame contains a "frame-check-sequence" (a CRC). The protocol contains a number of other implementation details, such as NRZI encoding, and ...
1
vote
0
answers
56
views
DS90UB948-Q1 internal pattern generator
Does anyone have prior experience with DS90UB948-Q1 FPD-Link III Deserializer deserialiser from Texas Instruments ? I am trying to configure the internal pattern generator block sending I2C commands. ...