Stack Exchange Network

Stack Exchange network consists of 175 Q&A communities including Stack Overflow, the largest, most trusted online community for developers to learn, share their knowledge, and build their careers.

Visit Stack Exchange

Questions tagged [dsp]

DSP stands for Digital Signal Processing or Digital Signal Processor.

1
vote
3answers
65 views

Inherent DC Bias in ADC sampling

I was just simulating the quantization behavior of ADCs of different bits, on data sampled by a 24-bit ADC. What I noticed that as we go towards ADCs with less bits a DC bias in the signal becomes ...
1
vote
2answers
72 views

Configuring Frequency Bandwidth and Input Signal for Bandpass filter circuit

How do I set and configure the frequency bandwidth I want the filter to output to a device? I am using a physical passive bandpass filter which I intend to take the signal in and filter it and output ...
0
votes
2answers
28 views

Load vs LDAC pins

Alright, so I'm using a TLV5628 Octal 8 bit DAC with my stm32f4-Nucleo and I'm kind of confused about the difference between LDAC and Load. I am also trying to figure out the clock rate and I might ...
1
vote
1answer
174 views

Best Approach Methods for Signal Processing

I'm looking for some advice, I am hoping one of the many forum experts could help me with some advice on the sampling and processing of signals. I am using an STM32F4 processor with 12 bit ADC and DSP ...
0
votes
1answer
73 views

Translating/reverse engineering firmware commands

I'm trying to build my own Hi-Fi system. So, I recently ordered this Japanese DSP that's able to process Dolby audio. I was all excited until the part had arrived and I found something in the ...
0
votes
1answer
36 views

Can I2S tdm interface send more channels with less sampling frequency?

We have a arm SoC(system on chip) connected with I2S to a DSP (digital signal processor). SoC and DSP both support 48khz, 8 channel and 16bits in TDM mode. Is it possible to use this interface to ...
0
votes
1answer
342 views

3 phase BLDC sinusoidal drive using PWM controller and/or DSP?

My background is mechanical engineering (robotics). I apologize in advance. I have a sensitive torque ripple (Vibrations) application and would like to use sinusoidal drive to run a 3 phase BLDC ...
0
votes
1answer
348 views

Anti-Aliasing Filter example

I need help in solving the below question. Bandwidth of the signal is 1KHz. Use a 12-bit ADC with SNR of 78dB for sampling. the sampling frequency is 12KHz. Choose suitable filter order and cut-off ...
0
votes
1answer
38 views

DSP board TMDX5505EZDSP potentiometers and switches

I have to do a project for school that is an audio effects processor but I'm not experienced with dsp. I'm using the Texas Instruments TMDX5505EZDSP. I've programmed some audio effects based on some ...
2
votes
0answers
482 views

FIR Lattice Filters

In DSP, sometimes the so-called Lattice Filters are use, having a structure like on this picture: I wonder what the advantages of the Lattice structure are, compared to other FIR filter types and ...
2
votes
0answers
266 views

RC filter - compute output as a function of input for generating waveform

I'm not so deeply into the theory about all this, I may use strange terminology... If I put a square wave through a simple lowpass RC filter, the output will be a sort of "rounded sawtooth", well not ...
1
vote
0answers
345 views

Wrong FFT result when using rfft function on STM32F4

I'm trying to use rfft function in STM32F407G and I am getting wrong results when I compare it with an online fft calculator . I give a sample input as {1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,...
1
vote
0answers
65 views

Non equal phase currents at nominal speed vector control Permanent magnet synchronous motor

I working on my implementation of vector control for PMSM. I'm having close loops over speed, current in d axis(flux loop), current in q axis(torque loop). I'm using MATLAB/Simulink for vector control ...
1
vote
0answers
61 views

dsPIC33EP512GP502 -> ADPCM?

It seems that ADPCM is all but non-existant anymore. But I'd like to use this to compress six high-quality audio channels into a smaller bit-stream with little overhead. There seems to be a dsPIC G....
1
vote
0answers
135 views

RMS calculation of signal with high crest factor up to 10 MHz

I'm attempting to measure the RMS of an AC signal with a crest factor of up to 10, at frequencies of up to 10 MHz. From my brief research I can see many ICs that work well above 100 MHz (designed for ...
0
votes
0answers
80 views

Time delay using IIR filters

I am trying to implement a cardioid pattern with two microphones. I was reading this paper titled "Digital Filter Array Optimization for Directivity Pattern". The link to download the paper is this. ...
0
votes
0answers
54 views

Amplitude-Frequency spectrum

I am tasked to find the amplitude of the first harmonic of a square wave. I did a time domain fourier series and plot a frequency spectrum I also did a frequency domain fourier series and plot a ...
0
votes
0answers
125 views

How to change step pulses into PWM pulse synchronously?

I am driving a stepper motor using microstepping techniques. For the input signals to the driver, step and dir are used. More than 100,000 steps/second speed is target. The PWM frequency is below ...
0
votes
0answers
93 views

FIR Filter delay calculation for cascaded filters

I have created a simulink model which had two filters implemented with an FIR block cascaded in series. The first filter in my case is a moving average filter and the second one a Gaussian filter(...