Questions tagged [eagle]

EAGLE is a low-cost PCB design software package.

Filter by
Sorted by
Tagged with
0
votes
1answer
142 views

Why I could not change this eagle NFC class6 antenna footprint?

I am designing a NFC board prototype that uses NT3H1101 chip. For this, I use NXP AN11276 antenna design guide. This document contains sample file download links for class 6 antennas. I downloaded ...
1
vote
2answers
164 views

Where is the correct place for a body pad of a TO220 linear regulator in Eagle

In my two-layer pcb design I have an LM317 with a TO220 package. I took the generic TO220 package from the default "linear" Eagle library which does not have a polygon copper pad under the body of the ...
0
votes
1answer
177 views

Ground planes in Eagle PCB

I have designed a PCB in Eagle. I have doubt regarding creating the ground planes. I have created a ground plane on the top layer only But I even have connections in the bottom layer too which are ...
0
votes
1answer
45 views

How to delete graphics from PCB board view in Eagle?

I am making my first PCB, and I have a numpad and a 16x2 LCD in the schematic. When I go to make the board, it also brings in the graphics along with the pins, but I will not be soldering them ...
1
vote
2answers
182 views

Is there any PCB design software/extension that can do automatic components placement?

I made a lot of home made PCBs, but I have a great problem concerned about the design, I am just an electronic hobbyist at school so I don't have that mind of electrical engineer to place components ...
0
votes
1answer
130 views

How to change the highlight color in Eagle when using the show command?

I want to use "show GND" and have everything highlighted show up purple. How do I achieve this?
0
votes
1answer
56 views

Is there a rule of thumb for choosing polygon width?

I am currently using the same width as the smallest wire inside the polygon, is this too small?
1
vote
1answer
83 views

Hidden airwires in Eagle …?

I have designed a PCB using Autodesk Eagle. After I routing the PC and check for errors from Tools -> Errors, there are lot of airwires (31) like below. But, I couldn't find any airwire. How to ...
6
votes
3answers
283 views

What are the common footprint naming conventions

This question is ultra verbose, but I'm doing this in an effort to help other newbies (like me at the moment) as they first get into a CAD program like eagle. In the past when I've been new to a field ...
0
votes
1answer
88 views

Altium PCB design [duplicate]

I designed a schematic diagram to design a PCB. But when I want to update the PCB from the schematic, there are several errors. I can't determine the problem.
0
votes
2answers
83 views

Molex USB Micro AB Eagle Package

I am creating a package for Molex's MicroAB USB 47590-0001 component because I could not find one for Eagle. My question is will this work to create the custom slots as seen in the datasheet? I've not ...
0
votes
0answers
27 views

Eagle CAD micro Thermal Visa

To put a thermal pad in Eagle you just put a via and connected to ground or change the name to GND, my question is how can we make thermal vias similar to the below image (via without copper on top or ...
1
vote
1answer
95 views

Can Vias be used on the board for branching tracks?

I need to split the RST line in two directions and also connect it to the opposite layer of the board. I did it like this: Is branching the RST line the right decision?
0
votes
0answers
76 views

Create Nixie tube pin connector socket in eagle cad

I am unsure how to properly layout a socket for a nixie tube in eagle cad. I'm especially unsure how to match the exact dimensions and what tool in eagle to use to create a hole with copper on both ...
1
vote
2answers
63 views

Allowing redundant tracks in EagleCAD

I have a 2-layer PCB, where I'd like to connect the top and bottom layers of two pads with a trace. However, when I try to connect one layer, the other layer simply disappears, as shown below, where I'...
0
votes
1answer
103 views

Make a caption n a copper layer in eagle

Read all the internet but cannot find how to make a caption on the copper "ratsnest" (either top or bottom) in Eagle. I want to make it "negative", i. e. no copper where letters are supposed to be. ...
1
vote
1answer
158 views

4 layer stackup Eagle

Can someone explain to me how I can change the layout order of my 4 layer board in eagle. I'm sure this is really a silly question, I'm coming from Kicad so I'm a bit green here. It's not obvious ...
2
votes
1answer
92 views

EAGLE - VIAS are smaller on the screen than in the actual gerber

Hi I have upgraded EAGLE to 9.5 and have one quite serious issue. The VIAS are displayed smaller than in the actual gerber file or manufacturing preview. Do you know the option which will force Eagle ...
0
votes
1answer
65 views

EAGLE. Differential pair routing. Width of the track changes after first change of direction

I try to route differential pair of tracks. When I click the mouse to change the direction it also changes the width
0
votes
0answers
33 views

Eagle Via Pairs From/To Different Layers with Through Holes only

I am using Eagle 9.5.1 premium and I cannot figure out how to create a layer stack to use Via pairs from (say we consider a 4-layer PCB) 1-2, 1-15, 1-16 using only through holes, since my design ...
0
votes
1answer
59 views

Create open copper plane in EAGLE

I need to redesign an old PCB and for that I want to put down a open copper plane that won't get covered by solder mask. I tried it by creating a rectangle in the 'Pads'-Layer. The PCBs just arrived ...
1
vote
2answers
248 views

PCB: ground plane thermals (in Eagle)

In a previous iteration of a PCB layout, I added a ground plane fill as recommended by many tutorials online (eg Sparkfun). By default Eagle creates thermals to ease soldering to the ground plane, but ...
1
vote
1answer
30 views

Eagle: Alternative to Pinswap for GPIO expander

I'm working on a PCB which is basically multiple MCP23017 GPIO expanders driven from I2C. As I layout the board (in EAGLE), I frequently find places where using different IO pins would avoid vias and ...
1
vote
1answer
163 views

How to place through solder pads of different shapes in EAGLE?

I searched everywhere and watched many eagle tutorials, but I couldn't find out how to place circle and square through hole solder pads. In the Eagle parts list, I only found the octagon solder pad. ...
0
votes
2answers
79 views

When making power polygon , making polygon on the smd-pad has any problems?

I'm now making 4 layer PCB and my PCB has one Power plane (L3) and one GND plane (L2). Now I just make a connection with inner layer (L3) with Top plane(L1). At this point, I'm curious that what is ...
5
votes
2answers
290 views

Hole partially through PCB

I'm trying to make a hole partially through a PCB in Eagle to allow a reverse mount led to shine through to the other side. I got this idea when I saw a torch shine through a pcb where there was no ...
0
votes
1answer
120 views

Are pads from the EAGLE “testpad”-library printed?

just a quick question. Are EAGLE "testpad"-library printed or seperatly bought and mounted? E.g. "testpad / PTR1" TEST PIN Footprint: B1,27 (Version 1) TEST PAD 3D Package: B1,27 (Version 2) TEST ...
0
votes
1answer
152 views

Name of these connectors

I am designing a PCB Schematic and I need to find these two components. Could anyone please tell me which components are these? 1 Also, I am making a circuit with 3 multiplexers so the idea is to ...
0
votes
1answer
84 views

Placement of the microcontroller on the back of the board with LEDs

I am designing a board with 9 SK6812 LEDs. On the back of the board I want to place the Atmega328P microcontroller. I have doubts whether the heating of the LED can affect the operation of the ...
0
votes
1answer
42 views

EAGLE - StopMask DRC Error

I cant understand what this DRC error means. Especially I do not understand this box. Does it mean that the Soldermask will cover part of the pad? How to correct it?
0
votes
1answer
18 views

Eagle UI: updating silkscreen of library component

I just finished a schematic in the free version of Eagle that contains 20+ 0402 resistors and about a hundred 0805 capacitors. I switched over to the board layout and found that the footprint of all ...
1
vote
3answers
41 views

Eagle UI: separating hundreds of components that are stacked on top of each other

I finished a complicated schematic in the free version of Eagle, switched over to the board editor and was encountered by this: In case the image doesn't say it all, there are about 100 components ...
1
vote
3answers
68 views

How to prevent voltage regulator board heating up and how thick traces should be?

Im designing a DC-DC voltage step down regulator based off of a switching regulator IC from texas instruments. I have designed the schematic and board accordingly and it should be able to supply 5A at ...
2
votes
1answer
151 views

Why does SOT89-ECB footprint exist?

Because of an oversight a part that has a footprint SOT89-ECB (PNP-BJT), ended up on my board, but when I tried to find a transistor that actually has compatible pin configuration I came out with ...
1
vote
0answers
265 views

Gerber viewer confusion - missing traces

I'm not sure about my gerber files. I guess there is something wrong. In different gerber viewers the PCB looks right. But in online viewers from JLCPCB and PCBway, the bottom view looks wrong. Some ...
3
votes
2answers
394 views

Eagle Drill vs. Diameter Parameters when making Through Hole Parts

I am working on making footprints in Eagle for a through-hole connector I want to use. I am running into some issues as I try to determine the appropriate diameter and drill size I need for the ...
1
vote
0answers
393 views

Importing EasyEDA project to EAGLE

I have a problem with uploading my EasyEDA project to EAGLE. Is there a way to open project from EasyEDA in EAGLE, I'm unable to find anything about it. EasyEDA exports files in .json format.
0
votes
1answer
114 views

Through hole via isolation in Eagle CAD 4 layers board

In Eagle CAD, in a 4 layers board (signal-ground-power-signal) how do I avoid that a through hole via from, for example, the top signal layer to the power layer is electrically connected to the layer ...
0
votes
1answer
59 views

Connect multiple source pins together to power signal in Eaglesoft

According to PCB shown below, I have a bunch of MOSFETs with HSOF package with 7 pins of source for each and failed to connect EVERY pin to the connector. In other words, when routing the source ...
0
votes
2answers
158 views

Charging a capacitor in Eagle SPICE

I'm trying to learn the basics of Eagle SPICE simulation with a simple capacitor charging circuit. My netlist is as follows: ...
1
vote
1answer
519 views

Eagle Library Missing Micro b Connector?

I'm not sure if this post belongs here or in another community but here we go. I'm working with Eagle cad (pcb) and i'm looking through the libraries and I couldn't find a single MICRO b usb connector....
1
vote
0answers
49 views

Eagle; Renumber Parts deletes everything in my schematic

I tried to use the renumber parts tool on my schematic (with default settings) and it deleted everything, leaving an empty schematic behind. There are some user defined parts in my schematic, but ...
2
votes
1answer
58 views

Eagle create board from schematic is missing some parts but ERC says they are consistent

I have capacitors C1 through C6 on my schematic, and if I type MOVE C2 into the command line it grabs that capacitor. But on the board created from my schematic, it is missing C2 and C3 and no other ...
0
votes
3answers
623 views

How to remove solder mask in Eagle

I want to remove solder mask in particular area for mount a TO220 package. As shown in below image I want to mount the 7805 using a M3 nut and need to remove solder mask only in covering area. (like ...
1
vote
1answer
55 views

Create new component based on existing one in Eagle 9

How can I create a new component in Eagle 9 based on an already existing one? It used to be a relatively straightforward endeavor in all the previous versions prior to v9.0 but the process seems to ...
0
votes
2answers
48 views

connect pad inside component symbol

I'm trying to connect A4 to pin 5 in 6050 in the picture. When I click those with the net tool, it also connects A2, which is not what I need. If I use the delete tool and erase the junction, they ...
0
votes
1answer
56 views

DUE schematic doubt Altium

I have the schematic of Arduino DUE for EAGLE software, I found a part I dont know what means for Altium Software. Can somebody tell me what is it "ETH" ? A header?? Arduino Due schematic I found ...
0
votes
2answers
112 views

What is this symbol in Eagle and equivalent for altium

I only use Altium Designer. Today I found an arduino due schematic for Eagle PCB Design Software and I saw a symbol I don't know. What is it, and what is the equivalent in Altium Designer? Is it a ...
-3
votes
1answer
165 views

ssd1306 (30 pin) oled display eagle library

I am designing an electronic project in Eagle PCB software. The project having a 30Pin SSD1306 Oled Display. I searched in the internet for the eagle library and i cloud not find a matching one. The ...
0
votes
2answers
51 views

Eagle automatically making connections to layers of PCB?

I'm designing a 4 layer PCB, using positive and negative power planes along with a ground plane and a top signal layer. While making the schematic I've notice strange little Xs in some of the through ...

1
2
3 4 5
18