All Questions

Tagged with
0
votes
0answers
48 views

Is normal SPI device compatible with SPI I/F?

Audio controller AK5374 that I use requires EEPROM with SPI. However, in the specs it is written, that it communicates with EEPROM via SPI I/F. Will normal EEPROM be compatible with this interface?
0
votes
0answers
95 views

ENE KB9012 SPI protocol reflashing with parallel port

The story in short: I have a laptop which got bricked with a failed BIOS update, and it's ENE KB9012QF A3 KBC's embedded flash contents needs to be reflashed. Solutions I tried, but didn't work: ...
0
votes
1answer
62 views

EEPROM 25LC1024 issue with PIC32MX OLIMEX board

I am trying to read the status register for the EEPROM following the instructions in this Application Note. I wanted to have the opinion of the community on the signals I am getting. They don't seem ...
1
vote
1answer
83 views

SPI software select not staying low

...and a few other things. I am working my way through Geoffrey Brown's book Discovering the STM32 Microcontroller and it's largely been smooth so far. I've come across an exercise where the reader ...
0
votes
0answers
52 views

Ambiguous behavior while using 2 SPI's with relatively similar speeds STM32f030c8

I'm using RFID reader Rc522 communicating with the STM32f030c8 via SPI1 and EEPROM communicating via SPI2. System clock : 48 Mhz (via the Internal PLL system) APB peripheral clock which has the SPI's :...
0
votes
2answers
148 views

SPI timing of 25LC1024

I'm using an EEPROM chip from microchip, it's doc gives the read/write timing as below: I'm a little confused. From FIGURE 1-2, I think it will read data in at the rising edge of SCK. But from FIGURE ...
1
vote
1answer
70 views

How to select specific programmer from multiple when using flashrom

I have 4 CH341A programmers connected to my laptop. They are all connected to the same USB hub. Reading the content of a SPI EEPROM works fine. How do I select the programmer (of these 4) to be used ...
8
votes
1answer
3k views

SPI data storage devices: (micro)SD card, DataFlash, or serial EEPROM?

I am revisiting some of my design habits, and one of them is under serious scrutiny: the go-to SPI-based storage device is (micro)SD cards, for their price-to-capacity ratio and generally higher ...
3
votes
2answers
11k views

USB, UART, SPI difference and usage? [closed]

I am trying to enabling an embedded system built around Intel D1000 MCU. I am mainly from a software background and just starting to catch up with some hardware knowledge. I am trying to build ...
0
votes
1answer
365 views

Atmel SPI Serial EEPROM Writing Error - Page Write?

I'm using this EEPROM: Atmel AT25640B SPI EEPROM DATASHEET It seems pretty straight forward to operate and I've followed the datasheet closely when coding my driver. I seemed to have some success ...
3
votes
2answers
493 views

Will an SPI EEPROM chip have the same issues with non-atomic write operations as a dsPIC's internal EEPROM? [duplicate]

A while back I had some intermittent trouble with the internal EEPROM of a dsPIC. Every so often, some value in the EEPROM would be found zeroed out on power-on. I tracked the problem down to when the ...
6
votes
4answers
1k views

Will an SPI flash memory chip have the same issues with non-atomic write operations as a dsPIC's internal EEPROM?

A while back I had some intermittent trouble with the internal EEPROM of a dsPIC. Every so often, some value in the EEPROM would be found zeroed out on power-on. I tracked the problem down to when the ...
5
votes
1answer
8k views

How to write to 93LC46B EEPROM from an Arduino using SPI

I have a question regarding eeproms and an Arduino (I am using Arduino Uno). I have the following eeprom: 93LC46B. From the datasheet I understand that in order to write the integers ...
4
votes
3answers
749 views

Intermittent SPI bus

I'm attempting to interface a PIC18F4520 to a 25LC640 via SPI protocol. I'm using the built in MSSP hardware of the PIC. The PIC18F4520 is the only master on the bus. I'm reading 16 bytes of data from ...