Questions tagged [eeprom]

Acronym: Electrically Erasable, Programmable Read-Only Memory. Sometimes used with Flash parts that are similar to old EEPROM parts.

24 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
2
votes
0answers
299 views

Problem with writing eeprom memory

I am trying to write atmel at28c256 on breadboard so I tied all address lines to ground, and all I/O lines also tied to ground. I untie I/O lines for reading, tie 'WE to high, 'CE to low, and 'OE to ...
2
votes
0answers
829 views

Why is so8 test clip causing read errors with 93C56 eeprom (TL866 programmer)?

I am trying to read an Atmel 93C56B eeprom, so8 surface mount package, with this programmer. When using the so8 adapter in the zif socket it works perfectly. However when I use the test clip, it is ...
1
vote
0answers
33 views

PIC16F7X I2C Issues With 24AA01/24LC01B EEPROM

I have an existing PCB that is no longer supported by the manufacturer and has been plagued with software issues for years. So i don't have much control over how the board is laid out and what ...
1
vote
0answers
44 views

How to program i2c eeprom by hand?

I have a 24c02 eeprom and I want to program it. But I don't have Arduino or any microcontroler. I saw a video about program eeprom by hand, but they are parallel eeprom. This is the link of that video:...
1
vote
0answers
157 views

Replacing SD card by using EEPROM

I am using the mbed platform and to be specific, NUCLEO L073RZ. To log data, I am using SDFileSystem.cpp that is officially supported by mbed (you can find the link ...
1
vote
0answers
149 views

Problems programming a 29GL256

I've been experimenting with Python scripts and using an Teensy 2.0 ++ to program different flash memories. So far I've found a script to program a 29GL128, which works perfectly, but I'm trying to ...
1
vote
0answers
105 views

EEPROM in Simulator for Microchip Pic18f

When programming a Microcontroller from Microchip using Pic18F and using XC8 Compiler, can i use Simulator to test / verify it ? ...
1
vote
0answers
437 views

PIC : EEPROM not write properly to 0xFF in PIC18F67K22 controller

I am writing values from 0x50 to 0x3ff in EEPROM of pic18f67k22. Whenever eeprom is getting full, I am writing 0xFF and then after write my data from 0x50 location. but some time eeprom is not write ...
1
vote
1answer
508 views

Why there are AC timing characteristics but not DC in I2C interfaced chip?

I'm quite newbie in electronics, and I'd like to learn why there are AC timing characteristics to this particular EEPROM (24LC512) that I'm using but none for DC? Does AC timing constraints apply to ...
0
votes
0answers
31 views

Reverse Feedback protection in a RC circuit

I have been working on a model CPU build from LS TTL ICs for the past couple of weeks. I am going to give a little background here, during the prototyping I stumbled upon several intresting issues ...
0
votes
0answers
60 views

Why bad data is read from SPI Flash

I have a device in which there is a SPI flash and a I2C EEPROM, W25Q256JV (32MB) and AT24C1024 (1MB) respectively. The MCU writes data packets in the flash fifo and saves its read write pointers in ...
0
votes
0answers
124 views

Proteus Atmel EEPROM Simulation

Can somebody confirm me if Labcenter Proteus can simulate the EEPROM registers for the Arduino Atmel megaAVR ATmega328P, for the standard instructions EEPROM.put ...
0
votes
0answers
59 views

Is normal SPI device compatible with SPI I/F?

Audio controller AK5374 that I use requires EEPROM with SPI. However, in the specs it is written, that it communicates with EEPROM via SPI I/F. Will normal EEPROM be compatible with this interface?
0
votes
0answers
34 views

Msp430 f5328 Eeprom data get erased when burn new firmware

Hi is there anyway I can do this? I need to have my serial number in eeprom. But the problem is my data has been erased when I burn new firmware. Is there anyway I can avoid this. Thanks
0
votes
0answers
109 views

EEPROM and Flash testing

I am looking into the best practices for EEPROM and Flash memory testing. We are talking about end of line product testing by an ATE. The goal is to identify defect chip before writing memory content. ...
0
votes
0answers
62 views

eeprom endurance and life expectation

Imagine the following situation: 'considering that we have the environment of room temperature ..' EEPROM size: 512 byte. EEPROM endurance: 100,000 write cycles logging data: 4 bytes every 3 minutes. ...
0
votes
0answers
259 views

ENE KB9012 SPI protocol reflashing with parallel port

The story in short: I have a laptop which got bricked with a failed BIOS update, and it's ENE KB9012QF A3 KBC's embedded flash contents needs to be reflashed. Solutions I tried, but didn't work: ...
0
votes
1answer
68 views

EEPROM 25LC1024 issue with PIC32MX OLIMEX board

I am trying to read the status register for the EEPROM following the instructions in this Application Note. I wanted to have the opinion of the community on the signals I am getting. They don't seem ...
0
votes
0answers
165 views

Microcontroller(Atmega16A) hangs in Stop method while communicating using I2C with Atmega16 and 24LC256

First of all let me say that I am a beginner in embedded programming. I am trying to do write/read using I2C protocol from 24LC256 EEPROM using Atmega16A. While debugging in Atmel Studio 7, I see I ...
0
votes
1answer
42 views

Power Fail Monitor and ADC measurement

In my AVR project, I need to measure input voltage (before buck converter), and check for power loss to quickly save some data to EEPROM. Measuring input voltage is just to display its value, but I ...
0
votes
1answer
71 views

Combine two 8bit EEPROM to make 16bit EEPROM

I am working on building a computer out of logic chips. I want to use an EEPROM as the instruction memory. However, my EEPROM's only has 8bits data output, but I want my instructions to be 16bits long....
0
votes
1answer
51 views

Designing a Carry lookahead unit using EEPROMs, creates osclillator

I have read something about CLUs (Carry lookahead units) and want to build one. I have settled on design using eeproms as adders ...
-1
votes
2answers
148 views

Recording servo movements using pic with CCS C

Here what I am trying to do is control servo motor with a pottentiometer and record its movement using analog to digital converter and than play. I started with just moving the servo. To see which ...
-1
votes
1answer
1k views

How to test flash memory

I'm using blackfin533, and I would like to write a software for flash memory testing. How would I test the flash memory ? I know how to test an eeprom but how would I test the flash memory of the ...