The Stack Overflow podcast is back! Listen to an interview with our new CEO.

Questions tagged [fixed-point]

A number with a fixed number of digits before or after an implied decimal point. It contrasts with the floating point number representation. Often used in place of floating point numbers if hardware floating point unit is not present.

Filter by
Sorted by
Tagged with
1
vote
1answer
36 views

Interpretation of I2S data

I am working with a TI PCM1807 ADC (datasheet: https://www.ti.com/lit/ds/symlink/pcm1807.pdf) and try do some signal processing on a FPGA. The PCM1807 output is I2S. I was wondering how to interpret ...
0
votes
2answers
113 views

Pulse generator in Simulink Matlab

I want to generate a pulse in Matlab Simulink fixed point solver. The step size in the Simulink fixed solver is 1e-06, but I need a pulse width of 2e-08. The figure shows the clear requirement of ...
0
votes
1answer
203 views

How to convert fixed point binary numbers to BCD? [duplicate]

I am trying to make a calculator that can do fixed point calculations but I don't know how to display them in decimal (BCD). People have told me to use reverse double dabble but I am looking for ...
1
vote
1answer
2k views

Use floating values in VHDL code

Assume I want to have a continous sine signal as input to my VHDL code. The values will be of type float since it will take on non-integer values for example: 10.5 mA. How do I manage these numbers ...
1
vote
1answer
437 views

Range of unsigned fixed point division in VHDL

I was thinking about the range a result signal should have to acommodate an unsigned fixed point division. Suppose we have: SIGNAL a : UFIXED (3 DOWNTO -3); SIGNAL b : UFIXED (4 DOWNTO -2); am I ...
0
votes
2answers
1k views

How to represent Negative real numbers in Fixed Point representation

I find this module for the addition of two Fixed Point Numbers. Manual for using this Module: https://opencores.org/project,verilog_fixed_point_math_library,manual How to add -1.5 (or any negative ...
1
vote
0answers
576 views

RFFT on 8192 samples in Q15 with CMSIS

I need to perform an FFT on a block of 8192 samples on an STM32F446 microcontroller. For that I wanted to use the CMSIS DSP library as it's available easily and optimised for the STM32F4. My 8192 ...
2
votes
1answer
2k views

How to break multi digit number into separate digits in VHDL?

I found the method for c language.But I do not know how to perform this in VHDL. Let a fixed point number (12 downto -19) like 3456.478396 I need break this number entirely into separate numbers 3456....
0
votes
2answers
91 views

Two single-precision versus one double-precision unit

Suppose you are designing a floating point unit, and it is desired that it be capable of both single precision and double precision operation, in the former case not by simply expanding the single ...
3
votes
2answers
3k views

Why does signed (2's complement) binary multiplication have different procedure than unsigned?

The 2's complement binary multiplication does not have same procedure as unsigned if the both operands do not have the same sign. What is the logic behind that? Does special consideration apply to ...
0
votes
1answer
599 views

Can fixed point division be implemented using a divider that outputs quotient and remainder?

From what I have seen, division is a highly expensive operation in terms of time or area (tradeoff). It is usually implemented as an operation of continuous subtraction of a number from another number ...
0
votes
1answer
898 views

Is it possible to show fixed point numbers as base 10 in modelsim wave?

If a person is creating a system using fixed point numbers a decimal point is implied. In this case, if one is going to use the wave window to see the result, it will be beneficial to see the actual ...