Questions tagged [fuses]

Questions regarding physical fuses. Fuses are a safety device consisting of a strip of wire that melts and breaks an electric circuit if the current exceeds a safe level. PPTC, PTC, and Polyfuse questions should use the Polyfuse Tag. Please keep in mind that repair questions are typically closed if not within the scope of the Site and FAQ.

Filter by
Sorted by
Tagged with
0
votes
1answer
334 views

Why did my Atmega328p chips stop working?

I am fairly new to embedded programming. I bought some Atmega328P U chips (not Atmega328P-PU). I have two Arduino boards and the chips worked just fine, and were letting me upload sketches. One of ...
2
votes
3answers
739 views

Can I replace a 12a fuse with a 15a fuse on a 12v - 120v automobile inverter?

I'm hard wiring an inverter into my automobile. Tapping into a 15a fuse in the fuse box. To hard wire it I had to remove the "cigarette plug" and in so doing removed a 12a fuse. I have an inline fuse ...
0
votes
0answers
187 views

PTC or One time Fuse or fusible resistor for li-ion protection.any suggestion?

I designing a kind of portable device ,it contains 450mAh Li_ion or Li_Poly Battery (depends on space on PCB). I design this system for mass production (10k-20K). I want to add overcurrent protection ...
29
votes
2answers
4k views

What type of glass fuse is this and what does the spring do?

This is a standard sized glass fuse like what cars used before the 80s. I can faintly make out 20A, but I’m not sure what to call it in order to find a replacement. The fuse in the picture has not ...
0
votes
1answer
77 views

Poly fusing external peripheral device

The design I am working on is having peripheral connector with +5V power in it providing the voltage to the would-be connected device. There's relatively a long way inside the design from the ATX ...
0
votes
1answer
58 views

Pin protection fuses

A colleague of mine created the following circuit with the 3x 5A fuses for protecting the power connector pins from oxidizing and melting the connector plastic (we had some cases, when the connector ...
1
vote
0answers
255 views

Using thermal fuses in parallel?

If one has some 216C 10A thermal fuses, could one wire two in parallel in order to fuse a 10A heated bed on a 3d printer? The bed is 110V and 1100W btw, so in normal operation it should draw 10A. ...
0
votes
1answer
74 views

Can I use a simple fuse to protect a CMOS over current?

I'm designing an output with a MOSFET transistor to control loads such as relays, motors or incandescent lamps, similar to the outputs of a PLC. Obviously, there is no problem as long as the load ...
1
vote
2answers
39 views

Should I look at nominal or max battery voltage for choosing resetable fuse?

I am building a LED/Camera control circuit that is going to be using a 14.8V Li-Ion battery as a supply. I want to put a resettable fuse to prevent short circuits from blowing up too much since this ...
1
vote
2answers
1k views

Using diodes for reverse polarity protection

I want to protect my circuit against reverse polarity, by simply adding two diodes in parallel between the + and - input cables. So if the polarity is reversed, the current will go through those ...
1
vote
1answer
113 views

Trying to source a PCB component (a slow blow fuse I believe!)

I’ve stumbled upon this forum in a search for a replacement part for a PCB that makes up a digital ballast for a HPS light used in basil clone production. I’m handay with a soldering iron but I am ...
0
votes
1answer
451 views

Can I use a transistor like a fuse?

I just started learning about transistors, so I was wondering if I could build a circuit where short circuiting across the load caused a transistor to cut off power (like a fuse). My idea was that ...
0
votes
0answers
44 views

Suggestions on simulating fuse characteristics electronically?

Assume that we have an isolation transformer 230V in 230V out and that we measure the output current with a current transformer with known transfer function. We compare the current to a settable value ...
2
votes
1answer
163 views

Safety switch "breaking capacity" vs. voltage

In the context of safety switch rating (fuses, circuit breakers, etc.), the concept of breaking capacity refers to the maximum electric current which can be safely interrupted by a tripping safety ...
-1
votes
2answers
96 views

Can i use 1 fuse for all the outputs to protect my power source from overcurrent?

Can i use 1 fuse for all the outputs to protect my power source from overcurrent by connecting the fuse to the ground wire? I have 3 outputs: 3.3V, 5V, 12V and i want to protect my power source when ...
0
votes
1answer
140 views

Does a 5A Car Fuse Blows in a 12 Miliseconds Peak of 6A, in a 220v Circuit?

Thinking here in using a 5A fuse in a certain circuit, but it may reach 6A sometimes for a mather of 10 or 12 miliseconds only. That way, would this fuse blow or it would sustain and blow only in ...
4
votes
1answer
162 views

20A or 30A fuse in 200A fuse clips -- is nesting reducers OK?

So, I am trying to figure out the cleanest way to make a 20A or 30A tap from a 200A circuit (single hot + neutral) that is being run through a fusible safety switch (NEMA style, as this is in the USA),...
2
votes
1answer
224 views

Need to substitute a fusible resistor in an inrush limiter in a PSU

HP 6023A PSU again :) This time R1, which is a 20ohm 7W fusible. The relay pulls 1s after power is applied and I assume that the general idea is to take the egde of the rather substantial inrush into ...
0
votes
1answer
209 views

How to chose resettable fuse for 24 V DC to 5V DC converter?

I want to use a 24V to 5V DC converter, the PYBJ10-Q24-S5 (https://www.mouser.fr/datasheet/2/670/pybj10-om-1548233.pdf). Page 7 of the datasheet, they specified the EMC Recommended Circuit which ...
0
votes
1answer
1k views

Can I use a 24V, 1A fuse for a 5V application?

I have a 5V power supply which needs protection. I only have a 24V, 1A fuse. Can I use this fuse for the 5V power supply. As Watt = R * I * I = V * I. As rated W is constant for a given fuse, will ...
0
votes
1answer
175 views

How to choose the correct fuse in a double paralled battery supply system?

Suppose I have the following system: simulate this circuit – Schematic created using CircuitLab As you can see we have: Two 500V battery with an estimated 500mohm average internal resistance. ...
1
vote
1answer
283 views

Fast-blow instead of slow-blow fuse in consumer hifi power supply

I have a power supply unit for a hifi pre-amp. The power supply takes a slow-blow fuse (T2.5A/250V). If I use a fast fuse (F2.5A/250V) instead, how likely is the fuse to blow during normal power-on?
1
vote
0answers
95 views

Problem calculating fuses

I am calculating a fuse and I'm having a bit of trouble. I have a 12v 2A power supply that I want to protect, so my first thought was to place a fast 250v 2.5A fuse in series so it should blow if a ...
0
votes
2answers
735 views

Why a double fuse is used in some applications?

In some DC applications in an isolated system (i.e. no grounding), sometimes two fuses are used: one is positioned on the positive (Vcc) line while the other is located on the negative (return path or ...
0
votes
1answer
115 views

Is it safe to go over a fuse holder voltage rating?

I am looking to buy a few online fuses and fuse holders for the mains power into a kiln I’m fixing up that runs on 240V and draws 45A. A thick 6 AWG wire connects to mains power, then is split into ...
1
vote
2answers
456 views

What is the advantage of putting capacitors in parallel with glass fuse tube

I have seen a board and I wonder to know what would be the advantage of having capacitor in parallel with fuse.
3
votes
1answer
1k views

How are OTP fuses in ICs implemented?

One-time programmable (OTP) fuses are common in ICs. How are they typically implemented, on the silicon level? I know that they generally work like larger fuses, i.e. they can be blown but not ...
18
votes
8answers
4k views

Why do fuses burn at a specific current?

We usually specify the maximum current that a conductor (such as a fuse) can handle without burning. But doesn't the conductor really fail when a certain amount of energy/heat has been dissipated in ...
0
votes
2answers
42 views

Can I use a 32x6mm catridge fuse with a fuse holder specified at 38x10mm

This is my first time incorporating fuses in my project. I am trying to source for some DIN rail mount fuse holders and the accompanying cartridge fuses. After much searching, I have found the fuse I ...
0
votes
0answers
112 views

Protection Devices in DC ciruits

I am putting together a design for a custom Electrical panel. The panel consists of mainly DC powered components (Sensors, Controllers). Components are to be mechanically positioned using a DIN rail. ...
0
votes
4answers
254 views

Fuse Identification

Would anyone be able to help me identify this fuse? The markings on it are: "51NM 250V 1.6A". It is a glass 5x20MM fuse, I am just wondering if it is a fast or slow blow fuse so I can order a ...
1
vote
5answers
672 views

Circuit to detect broken fuse

Consider the following circuit: [edited schematic] DC_gen1 and DC_gen2 are two +28V dc ideal generators. ...
1
vote
2answers
926 views

Placement of varistor with respect to fuse

My design includes a pretty standard AC/DC converter powered by mains for intended use at home. For overvoltage and overcurrent protection, I am planning to use a combination of varistor and fuse ...
0
votes
2answers
192 views

What voltage will blow a fuse with given load resistance?

What is the maximum voltage that a circuit with a 20ohm load and 2.5amp fuse can be connected so that the fuse does not blow? Can someone answer this with an explanation please?
0
votes
0answers
86 views

RCA VCR Fuse Question [duplicate]

I have an old RCA VCR (model number VR501) which contains a fuse in the power supply I am repairing. From the markings on the fuse I can only tell that it is a 1.6A 250VAC glass 5x20mm fuse, however I ...
1
vote
2answers
46 views

Old stereo with a blown fuse [closed]

I have an elderly but much loved Kenwood cd/radio/tape stack that has blown a fuse. The fuse rating is T800mAL 250volt. For reasons beyond me these don't seem to be available in the UK and the Amazon ...
4
votes
1answer
107 views

Identification: Is this an 150A fuse? Or something else?

Can anyone else identify this element? What is it? Seems to have 150A stamped on the left side - is it a fuse?
4
votes
1answer
311 views

Help Identifying Inverted Fuse Symbol

The following diagram shows fuses off each of the PT connections (standard IEC fuse symbol) but it also shows a fuse symbol with inverted colouring on the neutral connection. This second fuse also ...
2
votes
3answers
597 views

Is this fuse time-current curve wrong?

I'm looking at the datasheet for the Bel 0ADKC /0ADKP fuses. In it is this: These curves don't seem correct. Notice that the curves for fuses with >= 800mA asymptotically approaches a value that ...
0
votes
1answer
100 views

Trying to figure out fuse specs ("3/2 3AG 1A 250V")

I need to replace a fuse, and I'm trying to get my arms around the specs. The fuse is stamped "3/2 3AG", then "1A 250V". What does the 3/2 signify? Is that related to how fast the fuse is? Does "...
18
votes
7answers
29k views

Does it matter if a fuse is connected to the negative or positive terminal of a battery?

I am currently going through the conundrum of where to place a fuse in my DC battery-powered circuit to protect the circuit components and the DC battery. I've been googling for a definitive answer, ...
0
votes
1answer
294 views

Fuse for a heating element

I am designing PCB for a heating control system. I have planned to use PCB mountable SSR for the control the heater element. The SSR can handle maximum of 2A current and heating element not exceed ...
0
votes
0answers
152 views

Short circuit protection of lithium pouch cells in parallel

I want to put together a battery pack with 2 or 3 lithium pouch cells (for example SLPB11543140H5) in parallel, and a few more in series. Of course they have to have some kind of short circuit ...
1
vote
0answers
188 views

Dual diode connection for return path

I want to use the following dual diode for the return path with a fuse. The diode is dual with each diode rated 25A, the cathode is the same, which means I have to connect it like in the figure? Do I ...
0
votes
1answer
117 views

How to connect a fast recovery diode with 3 pins?

I have a fast recovery diode, part number D30FD60K, I would like to know how I have to connect it. The diode will be used as the return path in parallel with a fuse. Like shown in the diagram. Pin 3 ...
0
votes
2answers
70 views

Is it possible that a load can be destroyed if I am disconnecting all other loads in the circuit but one?

I consider myself as a beginner, so please don't be that hard to me. Can I theoreticaly destroy a unfused load if I disconnect all loads but one in the same circuit? In my understanding the current ...
0
votes
1answer
187 views

Why were the fuses not protecting the circuit? [closed]

I bought a Aprilia SR 50 Scooter with a "small" problem, the frontlight and the horn are not working, because the 10A fuse does blow up if the key is turned... I don't know what happened today, but I ...
0
votes
2answers
619 views

Need to replace a surface mount fuse. T10 L AC250V. Please help [closed]

Basically I have a device which seems to have blown a fuse. I've done some research and found that it's a "surface mount fuse" or smd fuse. My main questions are where can I find this fuse(or is any ...
0
votes
2answers
149 views

Choosing the right power cord for my PC adapter [closed]

I need to replace the euro power cord on my new PC with a UK one. The power adapter for the PC has the following rating: Input: AC100-240V - 50-60Hz, 3.5A Output: 19.5V (direct current) 11.8A The ...
1
vote
1answer
74 views

Question on fuses specifications

In the datasheet for fuses (for example, I'm looking at the Bel Fuse 0678L9150-02 -- datasheet at https://www.belfuse.com/resources/CircuitProtection/datasheets/0678L%20Jun%202016.pdf), they report ...

1 2 3
4
5
11