Questions tagged [glitch]
The glitch tag has no usage guidance.
21 questions
2
votes
0
answers
170
views
Z80 interfacing, address decoding logic produces noisy signals
I really would like to have suggestions and feedback from someone. It's about digital logic, in detail, the Z80 interfacing.
In this design, I used a 74HC30 which is a 8-input NAND Gate.
I'm using it ...
- 235
0
votes
1
answer
68
views
Clock/voltage glitching
Is it possible that clock/voltage glitching can happen over remote distances? (Having the necessary equipment.)
- 15
0
votes
1
answer
173
views
How to get rid of glitch?
I have designed simple P-channel MOSFET circuit. It works well, but when low source power is applied (1 V), a glitch occurs in the output signal.
I tried R, L and C component, but it didn't work.
What ...
- 11
1
vote
1
answer
3k
views
STM32 PWM and Output Compare
I have some simple firmware written for an ATmega328 (not Arduino) and I'm converting to STM32.
I have more than one STM32 development board, so for now I'm searching a generic config and generic code....
- 11
4
votes
0
answers
99
views
How to control DAC white noise at increasing sample rates?
A lot of background, the question is at the end:
I have made some simulations and experimental tests with the goal of achieving lowest possible noise floor using DACs with a sample rate of at least ...
- 23.4k
0
votes
1
answer
105
views
Question re voltage gain glitch LTSpice simple one BJT amp simulation
Screenshot shows a simple one BJT amplifier circuit in LTSpice, 100mV 800 Hz sinewave input with the output shown in the blue trace.
The green trace shows the calculated voltage gain i.e. Vout/Vin. ...
- 599
0
votes
1
answer
121
views
Determining cause of QSPI FLASH output glitches
I am testing a QSPI NOR FLASH device on a board I designed. It's datasheet is here.
Although it is working, I am seeing some glitches on the FLASH SDO (Serial Data Output) line. All other signals are ...
- 215
-1
votes
2
answers
66
views
Can hazards increase switching time and/or number of switchings?
In connection with question
CMOS gate logic switching time based on input vectors
one of the answers mentioned hazards. Although the question was about the switching time, finally I did not find the ...
- 101
2
votes
3
answers
2k
views
What is the difference between a glitch and a hazard?
Both glitches and hazards seem to be very similar. Can the difference be explained with the help of an example?
- 39
0
votes
3
answers
526
views
Getting glitches on GPIO using a MOSFET as a logic level converter
I need to connect an Event Detection pin (pin of the NXP NTAG 5 component) to a GPIO of the NXP i.XM6 processor.
The problem is that the NTAG 5 pin has a logic level of 5V and the GPIO has a logic ...
- 101
1
vote
1
answer
603
views
Glitches in clock gating cell
how exactly does glitch happen for rising-edge and falling-edge ICG ?
Why for the top version of rising-edge ICG, there is no X at the MSB of the latch output ?
Note: TE signal is asynchronous to CLK,...
- 423
0
votes
2
answers
146
views
Reasons for glitches observed on PCB from physical touch of floating enclosure
I have a circuit on a PCB on which I’m observing “analogue glitches” when making physical contact with the enclosure.
This enclosure is from ABS and there is a circular connector on one side for ...
- 2,705
0
votes
1
answer
407
views
Glitches on ring oscillator based on discrete logic gates
I built a ring oscillator out of discrete logic gates as in the following schematic:
It consists of 6 inverters/NOT gate (SN74LVC1G04@U12-17) and one NAND gate (SN74LVC1G00@U11) so the circuit can be ...
- 253
0
votes
1
answer
339
views
Counter glitching? Instability? Can't get a trigger lock on the scope, what might that be?
I have a 4 MHz clock and 4 x 74LS161 4-bit counters hooked up to get a 16 bit counter. It's all done how I have done it many times, synchronous with clock going into all the counters and RCO of ...
- 1,669
0
votes
1
answer
121
views
74LS652 shows peculiar glitching behaviors, what might cause this and how can I prevent this?
I am using 74LS652 octal bus transceivers and registers, in a 4 MHz switching application and I am seeing very peculiar glitching. Here is the focus of the problem:
and that 16 bit Counter is here
...
- 1,669
3
votes
3
answers
2k
views
How do you fix the glitches in the following Karnaugh maps?
The following circuit is supposed to output 1 if the input is greater or equal than 1010 (decimal 10). The truth table is given and we are supposed to convert that to POS and SOP using Karnaugh maps.
...
- 143
2
votes
3
answers
4k
views
Treadmill causes nearby electronics glitch
I don't know if it is right place to ask, if not correct/guide me.
I recently have built treadmill workstation, where I could walk and work (rather than just sitting).
But as soon as I turn on ...
- 131
1
vote
2
answers
180
views
Changing pin direction without glitching on LPC800
I'm looking at an LPC812 Cortex M0+ microcontroller and its GPIO functions. On a PIC microcontroller, one would always set the LATch prior to changing the direction of a given pin. This avoids the ...
- 2,588
1
vote
3
answers
534
views
A problem regarding my Slayer Exciter circuit?
I have made a Slayer Exciter circuit for my school project. I'm going to be assessed on it.
Now, it works just fine. But if I have to light a tubelight or something, I have to touch the terminal to ...
- 21
1
vote
1
answer
3k
views
debounce filter vs glitch filter [closed]
What is the difference between debounce filter and glitch filter on a mcu?
I'm trying to implement a hardware debounce filtering on a ATSAM4S4C
(ATMEL SAM CORTEX-M4 - PAGE 575. http://ww1.microchip....
- 2,074
1
vote
1
answer
1k
views
For oscilloscope, what are the differences for Glitch Capture Channel and Sample Channel?
I'm using a Tektronix oscilloscope and I use only one channel. I export the data for that channel to a csv file and open it on my PC. I found the csv file actually contains data for two waveforms! One ...
- 117