Skip to main content

All Questions

Tagged with
Filter by
Sorted by
Tagged with
0 votes
1 answer
320 views

Faster Timer0 overflow than 2 ms on Attiny85

I'm trying to get a Timer0 overflow with an overflow every 500us, but can't find a solution to get it so low. I'm running the Attiny85 on its internal 1 MHz clock, so I know it is not gonna be the ...
jonas's user avatar
  • 309
0 votes
1 answer
75 views

Problem or misunderstand of ADATE bit on ATTiny45

I have 2 buttons connected to pulled-down ADC input. I want to trigger ISR(SIG_ADC) when ADC finishes conversion - this is working. If I start ADC using ...
filimonic's user avatar
  • 209
3 votes
2 answers
2k views

Timer0 overflow interrupt does not work on ATtiny10

I am trying to use the Timer0 overflow interrupt to make a little project. I used such a timer in the ATtiny45 and it worked, but with ATtiny10 no result. So I tried an easy LED blinking program and ...
sepplhans's user avatar
  • 205
8 votes
3 answers
2k views

ATtiny13A - Can't generate software PWM with CTC mode

I'm trying to make a remote control RGB LED light using an ATtiny13A. I know the ATtiny85 is better suited for this purpose, and I know I might not eventually be able to fit the whole code, but for ...
Pouria P's user avatar
  • 320
0 votes
2 answers
2k views

Delay doesn't work (avr attiny 26, delay.h)

I am trying to learn how to write programs to microcontroller, and started with very simple things like LED blinking with given frequency, or controlled by button. However, I have problems with using ...
Antonio's user avatar
  • 103
2 votes
2 answers
2k views

Missed Interrupt Problem with Attiny85

I'm trying to use an Attiny85 (digispark) to wake another controller from sleep (an ESP8266). The Attiny is connected to an IR receiver which has an active low output. Basically I have connected an ...
localhost's user avatar
  • 302
1 vote
1 answer
1k views

Timer1 on ATtiny85 not working as expected

I am trying to use Timer1 on the ATtiny85 (Adafruit Trinket) to blink an LED every second. The prescaler value is 1024, and the compare register value is 28. I loop through this 279 times to get a ...
Suba Thomas's user avatar
  • 1,409
0 votes
1 answer
84 views

ATtiny861 pin change interrupt on PA.2: error in datasheet?

I faced with some confusion in subject datasheet: In one section PA.2 should be masking by PCIE1 bit as PA.2 is PCINT2 input and it should be within PCINT[7:0] and PCINT[15:12] range: On the other ...
Roman Matveev's user avatar
2 votes
1 answer
1k views

Attiny10 not triggering timer overflow interrupt while simulation (Atmel Studio 6)

I have problems simulating the timer overflow in Atmel Studio 6. The code is for an Attiny10 and looks like below. As far as I know I set all the neccessary bits to enable the counter (which works in ...
milkpirate's user avatar
5 votes
1 answer
823 views

ATtiny45 pin change interrupt PB5?

On the ATTiny45 data sheets it states that PB5 can be used as a digital IO pin and I want to use it to trigger a pin change interrupt, my only issue is that it is also the reset pin and the moment I ...
Gerharddc's user avatar
  • 285
2 votes
2 answers
9k views

How many external interrupts has attiny85?

The title is quite self descriptive. I ask this question because I found contradicting information in the atmel web page. I need two external interrupts to control one rotary encoder. One interrupt ...
Terrik's user avatar
  • 123
6 votes
2 answers
10k views

Calculate exact timer frequency for ATTiny

Trying to wrap my head around these overflow timers for the ATTinyx5 (45 in this particular case). I seemed to have a great handle on it with the ATMega328 but I cannot get it to work the way I want ...
Adam Haile's user avatar
  • 1,623
2 votes
1 answer
2k views

How to implement a synchronization signal with AVR (attiny45)?

In pseudocode I want to do following: ...
Juha's user avatar
  • 188