Questions tagged [maxim]
The maxim tag has no usage guidance.
14
questions
0
votes
0
answers
53
views
Potential Reasons for Fault on RS-485 Transceiver
I am working with the MAX3441 RS-485 transceiver, but I have run into faults with the three transceivers I have tested, so I am wondering if anyone can shed some insight on potential reasons for the ...
1
vote
1
answer
133
views
MAX32660 SPIMSS DMA documentation?
SPIMSS DMA examples are conspicuously missing from the MAX32660 SDK version that I have. Is there any documentation that explains whatever operating conditions are relevant to an actual SPIMSS DMA ...
- 397
0
votes
0
answers
38
views
MAX32660 SWD: Meaning of CSYSPWRUPREQ not asserted?
In a working SWD sequence generated by pyocd, the MAX32660 target's DP4 (CTRL) register has the CSYSPWRUPREQ bit set, as follows (as reported by the probe's console):
...
- 397
0
votes
1
answer
26
views
MAX32660 SWD SELECT does not affect the next AP read
I am trying to write my own PyOCD SWD probe module (because DAPLink is broken and nobody knows how to compile it, while the remaining 2 probes that PyOCD 0.26.1 supports, which we shall not name here, ...
- 397
0
votes
1
answer
45
views
MAX32660 SWD specifications?
Where can I find the SWD (Single Wire Debug) specifications for the MAX32660? I searched the user guide and data sheet, but could not find key SWD parameters such as signal timing, which features it ...
- 397
0
votes
0
answers
36
views
How to compile MAX32625PICO DAPLink firmware
I want to recompile the MAX32625PICO's included DAPLink firmware myself to fix the pin-wiggling code. Maxim distributes working firmware images on a page that describes them as licensed under Apache 2....
- 397
3
votes
3
answers
175
views
MAX32660-EVSYS SWD not working with longer cable
My MAX32660-EVSYS frequently fails to start pyocd and/or program the target when the ARM SWD (Single Wire Debug) cable (connecting it to the target MAX32660) is 12 inches or longer. It appears that ...
- 397
0
votes
1
answer
39
views
Connecting load to circuit resets MAX809
I have a MAX809T which partially works fine, outputting high when voltage is above the threshold after a small 1 second time delay, and outputs low when the voltage is below the threshold. It also has ...
- 138
1
vote
1
answer
76
views
0
votes
1
answer
19
views
Required supply power for MAX11301
I'm looking to use the MAX11301 for a project, in reviewing the datasheet i'm confused by exactly what the supply voltage required would be. I need to use some of the ports in the DAC analog output ...
- 25
0
votes
0
answers
43
views
Current measurement with MAX78630
Abstract
I am developing a "irrigation pump" energy analyzer. Irrigation pumps are controlled with Wye-Delta controller (in my country, soft starters are not used common). In these ...
0
votes
1
answer
58
views
Can someone confirm the typical application circuit of MAX664x Fan controller datasheet?
I'm planning to use the MAX 6644 for a simple fan control application. All in all the IC is very straight forward to use. However after analyzing the typical application circuits in the datasheet I ...
- 1
3
votes
3
answers
327
views
Should I include the resistance of capacitors and inductors (reactance) in my schematic?
I generated a DC/DC PS circuit from Maxim Integrated, and got this output:
You'll notice that both the inductors and the capacitors have their respective resistances marked (in milliohms). Are these ...
- 223
1
vote
0
answers
270
views
OpenOCD stuck listening on ports
I have a fresh install of Maxims Micros SDK and I am having an issue when I try to debug or even run on target. I get the following output on the eclipse console, it never gets past this listening ...
- 871