Questions tagged [non-inverting]

The tag has no usage guidance.

19 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
4
votes
1answer
244 views

Non-inverting op-amp saturating incorrectly

Background Hello, I'm trying to amplify an audio signal using an LM324N in a non-inverting configuration. I'm not trying to build an audio amplifier to drive speakers, I just need to amplify it a bit ...
2
votes
1answer
634 views

Simulating ADL5536 Gain Block with Ideal Amplifier

I'm trying to simulate the ADL5536 Gain Block in LTspice. A link to the datasheet can be shown below: http://www.analog.com/media/en/technical-documentation/data-sheets/ADL5536.pdf Analog Devices ...
1
vote
0answers
292 views

Issues with non-inverting op-amp Pspice sim

I want to build the circuit pictured here in Figure 1: When I simulate it, this is the result: For some reason, the output of the op-amp is always 183.8mV and if I work backwards using the ...
1
vote
0answers
501 views

Phase shift problems with ICL7611 op-amp

Update: This problem has been solved, the error was in another circuit that was providing the current and not with this. Note to everyone (and self): ACS712 is direction sensitive, even for AC ...
1
vote
0answers
2k views

The Op-Amps don't work correctly for this circuit [Thermocouple]

I'm trying to connect a thermocouple to an Op-Amp to amplify the output of a thermocouple. this is the circuit: Also for R17 I put a 5k09 resistor instead of 6k8 and for R18, 1k032 and for R19, 366k ...
0
votes
1answer
67 views

Stereo channel strip based on NE5532

I want to build a stereo channel strip, using the NE5532 IC. It should feature 2 mono inputs with volume control, mute switch and pan control going to a stereo output with unity gain. In the schematic ...
0
votes
2answers
68 views

Motion Sensor Design

I'm trying to design a motion sensor alarm. If there is movement in my house, the motion sensor will send out a signal which will be connected to an alarm that will make a loud noise. I'm currently ...
0
votes
0answers
88 views

Amplify 1kHz sine wave from AD9833 DDS using LMH6609 operational amplifier

I'm trying to amplify a 1kHz sine wave signal from the AD9833 DDS chip (0.6Vp-p) to a more usable level (6Vp-p) for a sort of function generator. I plan to work with higher frequencies as well. So I ...
0
votes
2answers
83 views

Op amp output DC operating point variation with load current

Consider a cmos op amp in non inverting configuration. For a small load current, we expect the output DC voltage to be the input DC voltage multiplied by closed loop gain. As the load current is ...
0
votes
1answer
50 views

Line input circuit

I'm trying to design an unbalanced line input for an audio device using a single supply. I would like the input stage to provide variable gain between 0 and 2. This is what I have come up with so far:...
0
votes
1answer
64 views

Whats the gain of this op amp?

what i did here is take current over the 4.7 kilo ohm and since there are no other voltage input other than the one then shouldn't the Vout be 0.2127 volts? thats not possible for a non-inverting ...
0
votes
1answer
63 views

Solving for adding a voltage to eliminate the non-ideality of the op-amp

The circuit as shown above. Conditions known: The op-amp is nonideal. Both inputs have current flow, lets say 0.7 \$\mu\$A. Only \$R_F\$ is known, which is 450 \$k\Omega\$. Open-loop gain is high. ...
0
votes
1answer
415 views

Do you know how to add VEE and VCC power strips to op-amp in Cadence that will be fit for simulation?

This is the built in Cadence OPAmp. I need to add A capacitor to the VCC wirep and Ground the VEE wire however, there is clearly not a VEE or VCC on this op amp. Also, I know that I could manually ...
0
votes
1answer
583 views

Making block diagram of an op-amp configuration

Hi everyone, I have to make the block diagram of the above configuration. Supposing the input capacitance of op-amp Cin, I've drawn this: A is the open loop transfer function of the OPA. B is the ...
0
votes
1answer
49 views

to design a 2nd Order Sallen-Key HPF

I am having trouble solving the following exercise. I am having trouble with the damping constant as you can see. It is giving me a gain less than 1. I am following my course notes but can't solve ...
0
votes
0answers
57 views

Ripple on input of Buffer, Non-Inverting

I am using M74VHC1GT125DT1G a non inverting Buffer IC. See attached image . I have capture input and output waveform,problem is even when my input is constant high the output is switching. MODEM TS ...
0
votes
0answers
258 views

Finding the frequency of opamp to get a specific voltage gain

In the following question, they ask for the frequency at which the gain would be 1.41 V/V. The dc or low frequency closed loop gain is 2V/V (6 dB). Is the solution of the following question done ...
0
votes
1answer
55 views

Why does my single-supply non-inverting amplifier produce a wierd shape (depending on earphones)?

I built this circuit: It is based on this design for a single-supply non inverting amplifier: When I tested my output waveforms with earphone A I got normal results: When I used earphone B, I got ...
-1
votes
2answers
2k views

Design a circuit using 1 ideal op amp whose output is Vo = VI1 + 2Vi2 - 9VI3 + 4Vi4

So, I've been staring at this problem for several hours now. I've watched videos on summing amplifiers, and the like--but nothing seems to show how to use 1 op amp in a circuit that acts as both a non-...