Questions tagged [ohms-law]

A well known relationship that describes the relationship between Voltage and current through a device's resistance expressed mathematically as V= IR. This formula says that voltage across the device is equal to the current through the device multiplied by the resistance.

15 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
1
vote
2answers
73 views

Parallel circuit with LED on one path and resistor on the other

I'm a beginner to circuits. Unlike many other questions, my circuit involves a parallel circuit with a LED on one path but a resistor on the other, as shown in the picture. Q1: assuming the LED has ...
1
vote
2answers
140 views

How to calculate induced current?

Suppose we have a closed loop with two resistors in series and at particular moment in time the induced emf was two volts .i want to know why do we use ohm's law in calculating the induced current ?
1
vote
1answer
54 views

Creating a small range, small baseline varying resistor

I am doing a design project on making a passive varying resistor device. I have a flex sensor that increases in resistance when you bend it. It has a 10k ohm nominal resistance and increase to 110k ...
1
vote
0answers
90 views

Why would venting an engine create a negative amperage on a generator?

I'm writing simulation software for a civilian helicopter. The helicopter has two engines and two generators. Normally, we calculate the amperage reading of a generator through Ohms. I = W / V. ...
1
vote
4answers
316 views

Calculating Necessary Resistance In Current Source Circuit

I have a problem where I must calculate the resistance required in R3 to have 1A flowing through the two 9.7V sources in the image below (i.e. Charging the batteries at a rate of 1A). I have ...
0
votes
1answer
75 views

120 Watts and 7.2 Volts, how many Amps?

For a project I need to switch on a simple handheld vacuum cleaner with an Arduino. I am thinking of using a relay or mosfet. I opened the case and a 7.4 V 2200 mAh Li-Ion battery powers the motor, ...
0
votes
0answers
41 views

How to calculate R for an AC load on a 3-ph system

I'm trying to calculate the resistors in an AC dummy load for a 3-ph system. A simplified schematic can be found below. The idea is to switch (with regular AC 1-ph contactors) some resistors on each ...
0
votes
0answers
55 views

What is the difference between voltage across battery and voltage across a resistor?

simulate this circuit – Schematic created using CircuitLab I am doing an experiment for a lab and I am confused as to what they are asking. They ask to measure the voltage across the battery, ...
0
votes
0answers
45 views

How to find the current value in this circuit?

Here is the question i am getting how to proceed after finding the voltage My attempt : Next part of solution:
0
votes
0answers
30 views

Verilog-A Current/Voltage/Power Inconsistency

I'm simulating a phase change material in Verilog-A and need to calculate the power across the material. The material is a resistor, so it satisfies Ohm's Law. Therefore, P = IV = (I^2)R = (V^2)/R ...
0
votes
0answers
97 views

Solving a circuit with node voltage method

I have the following circuit: Knowns: Iz = 80 mA R1 = 100 Ohms R2 = 150 Ohms R3 = 220 Ohms R4 = 330 Ohms R5 = 100 Ohms As I understand Gi stand for the current source internal conductivity, but ...
0
votes
1answer
361 views

How do I calculate expected output voltage of car audio amplifier with given conditions?

I have a 4-Channel Amplifier rated at 800 Watt RMS per channel @ 2 Ohm load. Channel 3 and 4 are preset to operate a subwoofer speaker while Ch 1 and 2 are set to operate mid-range speakers at ...
0
votes
1answer
59 views

Is my wire rated at a high enough current?

I am in the process of planning a speaker build. I am making sure my current wiring is up to the demands of a new system. The amplifier is a CV 1800, which can put out 9.5 amps at 4 ohms in stereo (...
-1
votes
1answer
72 views

Ohms law and a resistor

I've recently just learned from the Internet that a resistor reduce current. But when I measured the amps from the power supple to the resistor in series and then measured again from resistor to an ...
-1
votes
1answer
73 views

Find the current at the resistor

I've tried to divide current at 8A and then make a Kirchhoff voltage law between the resistor and dependent current source but I still can't solve it.