Podcast #128: We chat with Kent C Dodds about why he loves React and discuss what life was like in the dark days before Git. Listen now.

Questions tagged [pir]

A passive infrared sensor (PIR sensor) is an electronic sensor that measures infrared (IR) light radiating from objects in its field of view. They are most often used in PIR-based motion detectors.

16 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
1
vote
1answer
53 views

PIR Sensor for bulb in room

This has been very long since I left electronics but recently I restarted taking interest in it as hobby. I bought some PIR sensors from Aliexpress and found it is very simple to implement if I have ...
1
vote
2answers
223 views

PIR sensor (HC-SR501) with n-Mosfet transistor not switching off

I have none to less electronics background, with limited knowledge whatsoever. I've used some schematics from the internet https://www.youtube.com/watch?v=ugDPdgGekNo to put in place the below setup : ...
1
vote
0answers
259 views

Retriggering 3V PIR sensor with 555 timer circuit and LEDS

Hi y'all I'm putting together a PIR sensor circuit that will trigger a 555 timer in monostable and run a set of LEDS for about 5 sec all on a 3v cr2032 button cell battery and than reset until next ...
0
votes
0answers
19 views

can i modify hc-sr501 PIR sensor to work only at night?

i see that i can add ldr to Hc-sr501 pir sensor so it will work only at night,the output become high for a certain period if any motion detected . can i modify it so the output become always high at ...
0
votes
0answers
33 views

Noisy or malfunctioning PIR HC-SR505 sensor

I bought 5 PIR Sensors to trigger when movement is detected, using an Arduino. During bench tests, all 5 sensors show many false triggers. I wonder if all 5 sensors have something wrong, or whether ...
0
votes
1answer
41 views

PIR triggers relay without motion

simulate this circuit – Schematic created using CircuitLab I'm using a HC-SR501 PIR sensor and a 12V relay to switch between green (NO) and red (NC) on a LED strip, everything being powered by ...
0
votes
0answers
37 views

Joule Thief powered HC-SR501 PIR Motion Sensor & LED string

Following BigCliveDotCom's YouTube video, I was able to build a joule thief. I then built a HC-SR501 PIR Motion Sensor lighting a 4.5v string of LED fairy lights powered by either a 5v wall wart. or ...
0
votes
1answer
65 views

Convert continuous signal of HC-SR501 PIR sensor to a single pulse

HC-SR501 PIR sensor sends a continuous signal of 0-3.3V for the period of 4-8 seconds (depending upon the delay set). Is there a way/IC I can convert this signal to a single pulse of 1 sec, preferably ...
0
votes
1answer
231 views

Connect 240v PIR motion detector to Raspberry Pi

I want to connect a 240V PIR motion detector directly to my Raspberry Pi 3. Inside its plastic case I found 2 PCBs. One is the power supply board which has a 24VDC relay, a S9013 NPN transistor, ...
0
votes
1answer
186 views

Passive Infrared (PIR) Motion Sensor

I want to have the PIR Motion Sensor: https://www.adafruit.com/product/189 Used to turn on a light whenever it detects motion. Simple enough, but would it be possible to have this done wirelessly? ...
0
votes
0answers
203 views

Long Range Motion Detection solutions

I'm trying to find solutions for the security of an outdoor area (2km long and 1km wide). We want to detect any breach through the borders of the area, if someone sneaks in and/or someone goes out. ...
0
votes
0answers
233 views

Noise in battery powered circuit

I have designed a circuit that uses the TI CC1310 microcontroller, and has a daughtboard that has the PIR sensor and amplification circuitry from the from the TIDA-00489 http://www.ti.com/tool/TIDA-...
0
votes
0answers
25 views

Is there a standard to connect PIR sensors to own hardware?

Does anybody know if there is a standard to connect PIR sensors to own hardware. E.g., I've seen that V+, GND, VIN (with load resistor) are required, but is this all?
0
votes
1answer
137 views

PSOC 5 interfacing with PIR sensor

I am trying to interface the PSOC5 LP097 with PIR sensor to trigger the stepper motor for my Pet Feeder System. In addition, everytime the PIR sensor detects a movement, I try to send a mail using ...
0
votes
0answers
409 views

Relate Pyroelectric Passive Infrared Sensor analog output to the digital “motion detected” signal

I'm using a digital PIR sensors from the picture below. it outputs a high (3.3V) on motion detection, low (0V) when no motion was detected. The analog sensor component of this motion sensor is the <...
0
votes
1answer
992 views

PIR (HC SR-501) not working

I'm working with ESP8266 Wemos D1 Mini and HC SR-501 (PIR sensor) in one particular project (please, see the circuit image in annex). The question is the HC SR-501 stay always LOW. I tried change the ...