Questions tagged [psoc]

Programmable System on Chip. This is a chip containing digital and/or analog blocks which can be configured to create a very wide range of designs. It may refer specifically to the Cypress Semiconductor's PSoC, which integrates configurable analog and digital peripheral functions, memory and a microcontroller on a single chip.

12 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
1
vote
1answer
67 views

Psoc 4 ADC and PSoC Creator 4.2

I have been trying to read in values from the ADC of the Psoc 4700s, but I have not been successful with producing results. I am using the 10 bit ADC described in this datasheet, but I still can't ...
0
votes
0answers
12 views

Connecting PSoC 6 EINK alongside another sensor on the same board

I am trying to figure out a way to connect a CY8CKIT-028-EPD E-INK display shield and a MAXREFDES117 heart rate monitor to the PSoC 6 BLE board. The E-INK takes the entire space on the board, ...
0
votes
0answers
26 views

Anyone here working with the Cypress PSoC6? Having trouble running the blinky program

I have a PSoC 6.3 Pioneer Kit (HW REV 11) and am having trouble running any of my own (or example) programs on the PSoC. I have the latest PSoC Creator (V4.4) installed with PDL V3.1.4 and the latest ...
0
votes
0answers
26 views

PSoC5LP + Adafruit LSM303DHLC compass + I2C

I am trying to replicate https://jimmyutterstrom.com/blog/2015/07/12/psoc-tutorial-adafruit-lsm303-magnetometer-compass-module/ on the PSoC5LP. I managed to get Magnetometer readings, but the stay the ...
0
votes
0answers
85 views

millis() function for PSoC4

I'm replicating the function of millis() for the PSoC4 in order to store the timestamp of a signal's maximum amplitude. For this, I'm using a timer with a 1kHz to ...
0
votes
0answers
33 views

PSOC 5 LP negative input on adc delta sigma in differential mode

I want to use an adc sigma with negative voltage input, I am using this psoc : CY8CKIT-059 PSoC® 5LP. It's a bit unclear in the ADC config because the Input range Under the input options says : +-6....
0
votes
1answer
298 views

Power monitoring dificulties using ACS71020 30A SPI and PSoC 5lp

I'm currently developing a board for my dissertation that should monitor voltage, current and power consumption of a given load. For that purpose i chose to use the Alegro chip ACS71020, the one i ...
0
votes
0answers
27 views

How to power PSOC 5LP from boost converter

I have the CY8CKIT-050 PSOC 5LP development kit, and I have read that I can power my chip though boost converter (Page 16, last line), but I don't find any place where get information about how to ...
0
votes
0answers
109 views

PSOC 4 Bootloader will not work when P4[0] and P4[1] Connected to I2C bus

I have been desparately juggling the pin allocations on this project in the hope of freeing up the VREF pin, and thought I had managed to do so. Previously my system was successfully transmitting over ...
0
votes
1answer
411 views

How does this resistive pull up and resisitive pull down circuit work?

In PSoC Creator, there is a resistive pull up and resistive pull down. From the documentation, the initial drive of pull up is logic 1 when for pull down is logic 0. Pull Up: When the DR=1, the ...
0
votes
1answer
181 views

PSOC 5 interfacing with PIR sensor

I am trying to interface the PSOC5 LP097 with PIR sensor to trigger the stepper motor for my Pet Feeder System. In addition, everytime the PIR sensor detects a movement, I try to send a mail using ...
-1
votes
3answers
170 views

Need Help with Python Script - ' 4 Dollar Programmer'

I am working on an embedded project and have made my first PCB with a processor mounted on board. The trouble seems to be actually getting my code onto that processor! I was sort of banking on being ...