Questions tagged [rgb]

Short for: Red Green Blue. The primary colors in light. Mix them to create any imaginable visible color of light. Questions are typical in reference to RGB Leds, RGB Led drivers, and code related to mixing RGB light, but can include RGB Video Standard in VGA monitors.

27 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
4
votes
1answer
6k views

RGBHV (VGA) to YPbPr Converter and Waveforms?

Purely for hobby, I am working on an RGBHV (VGA) to YPbPr (Component) converter circuit for old games consoles modified to output RGBHV on a VGA cable. From the game consoles, the RGB signal is taken ...
1
vote
0answers
92 views

RGB to YPbPr (YCbCr) conversion and bright picture issues

I'm working on a specific RGB to YPbPr (component) converter. It is supposed to connect old consoles to a modern flat 240p supportive TV. However I have an issue with luma Y output part. Here is the ...
1
vote
0answers
107 views

How to convert arcade RGB video (2-5v p-p) to VGA (0-0.7v)?

I'm trying to convert arcade video signals (JAMMA) to VGA specifications. From what I've gathered, arcade video signals aren't standardized. They can range from 0v-2v or 0v-5v, etc. However, VGA ...
1
vote
0answers
35 views

Can I connect 2 power supplies for 16 meters LED RGB strip?

I've bought 2 sets of 10 meter LED RGB strip (7.2w/m) for a room. Then I've cut them to around 8 meters each to get 16 meters. Everything seemed fine but one thing, because it's 2 separate controllers,...
1
vote
3answers
512 views

Can you determine RGB pinouts with a multi meter?

I have a Swiftech Apogee XL2 that has an addressable LED inside it. I want to connect it to my other RGB setups but I need to know the pin signals and voltage of the LED. I have a multi-meter at the ...
1
vote
2answers
102 views

Controlling RGB led strip each color with a switch

I am creating a picture frame that will have RGB led strip surrounding the frame. There is no room for controller. Is it possible to wire a switch between every color cable so I can manualy turn on ...
1
vote
3answers
705 views

What power supply do I need for my LED light strips?

My set up is this: Power supply > RGB LED WiFi controller > 1 to 3 cable splitter > 2M cable (x3) > 132.5cm 120leds/m 5050 RGB strip (x3) I contacted the eBay seller about what power supply I would ...
1
vote
0answers
479 views

can't change LEDs states using PCA9685

I have a PCA9685 IC connected to i2c of cubieboard like board. Also OE pin is connected to one GPIO pin. I'm using ic2tools to communicate with PCA9685, I can read/...
1
vote
0answers
216 views

RGB Cable Assignments - help

I have a video cable D-Sub 9 pin. Someone know the connector pin assignments to do a RGB 3 bnc cable? Someone can help me? Below, the image of description of the cable
1
vote
0answers
633 views

Mystery while driving a NeoPixel Ring (WS2812) with a GEMMA (ATtiny85)

I am working with an Adafruit GEMMA and NeoPixel Ring 16 LEDs (ATtiny85 and 16 WS2812 leds) and trying to get a program to light the LEDs according to my "pattern" structure below, representing R, G, ...
0
votes
0answers
48 views

Consistency Concerns Between Series RGB LEDs in a String

My concern/question: If one has a string of series RGB LEDs (w/ independent elements) and was to light green to 100% and red to approximately 75% -- in an effort to illuminate the Amber color -- how ...
0
votes
0answers
22 views

Can One hook up several displays on the same RGB parallel interface?

I am working with a 800*480 24-bit parallel RGB LCD display. The required clock for the RGB interface has to be between 23 and 27 MHz (typ. 25 MHz). For testing purposes, I need to display "...
0
votes
0answers
54 views

Help needed for driving 160 nos - 1.5W RGB SMD LEDs (5074 footprint)

I'm a planted aquarium hobbyist and have been making DIY led lights with 3W LED chips (white and other colour leds in 4 separate channels) driven with meanwell LDD dimmed with arduino. However ...
0
votes
0answers
43 views

Best wire gauge for an RGB video signal

I'm trying to wire a CVBS-to-RGB converter into my car's monitor that only supports Navigation Maps with an old-fashioned ...
0
votes
1answer
35 views

RGB LED Resistor Value and Source Voltage

I am using a Common Anode RGB LED in my project(datasheet is given below) and the different specifications for each LEDs are giving me headache. In my schematics, as shown below, I have used ...
0
votes
0answers
51 views

RGB Illuminated Potentiometers

I'm currently designing a circuit using Alpha RV141F-40-20BL-B50K Potentiometers which feature a clear shift into which a 3mm LED can be inserted. My initial plan was to just fit a WS2812B ...
0
votes
0answers
106 views

Best practice to switch on 4 power supplies from one single source

First of all, I am a self taught maker with a passion for LED lights. So far I have built a few display signs for indoor applications, where one microcontroller is connected to a number of RGB Led ...
0
votes
1answer
601 views

RGB LED strip presets controlled by a switch via 2-pin connector

First, I apologize if my terminology is incorrect. I am out of my element, but trying to figure this out. I bought a cheap PC case in Korea, and it included an RGB LED strip on the front of the case ...
0
votes
0answers
47 views

Is there a physical (electronics) difference between Hue White and Color and Hue White Ambiance bulbs?

I'm curious if anyone knows if there's a physical difference between a Philips Hue White and Color bulb, which allows the user to set a complete range of RGB colors including white light color ...
0
votes
0answers
477 views

Red divider resistors for 5050 RGB strip coming from WS2811 chip

To split up a WS2811 data signal into discrete 5050 RGB 12V LED signals, I followed the example on the WS2811 datasheet and hooked up its outputs to a separate power supply. This example shows one ...
0
votes
0answers
44 views

Analogue Video Trace Matching

I'm working on an analogue audio, video and sync board for my Dreamcast. Something I've been wondering about is the tolerance for analogue video, specifically RGB, in regards to the delta for trace ...
0
votes
2answers
237 views

Wiring an RGB led light array

I'm building a grow light using 100 rgb leds. I know that I need resistors but I don't know how to calculate which ones to buy. Also before I buy the leds I have the choice between common cathode ...
0
votes
1answer
55 views

Switching backlight to RGB in the following monitor C24FG70

I have the following monitor: Samsung C24FG70. Is it possible to change the white led backlights with RGB leds? Possibly the smd APA102 with the following microcontroller: ESP8266. How could i hook ...
0
votes
3answers
5k views

Control Simple RGB LED Light Strip With ESP-01 Using Homebridge

What I am trying to do is control a simple 2m 5050 RGB Led Light Strip though a ESP-01 that receives http requests through Homebridge. I am doing this through the better-http-rgb Homebridge plugin and ...
-1
votes
1answer
97 views

30 Meter in series LED SMD 5050 60 led/m 12v RGBW

I want to run 30 meter Led length in series in a room on the ceiling. LED specifications (according to the supplier:) LED Type: 5050 RGBW LED Light Strip Quantity: 60 LEDs / Meter Working Input ...
-2
votes
1answer
104 views

What type of capacitor do i need for this delay?

I installed a set of LED RGB foot-well lights on my truck. When they turned on, they have a small half second glitch before staying constant. I believe that this is because the LED RGB controller ...
-2
votes
1answer
768 views

WS2811 RGB LED with arduino

I need to get this model of RGB working with Arduino , I can't find this model on the internet , it's says 12volts. I need to know how to hook it up ? and if there is an Arduino code that would be ...