Questions tagged [safety]

*Your* health and safety while working on electrical devices, and designing devices that will not shock, set fire to, or otherwise harm the user of the device.

Filter by
Sorted by
Tagged with
2
votes
3answers
2k views

Are solenoids/inductors dangerous to have exposed?

An inductor doubtfully will be in a position to be of harm, however a solenoid with 1A+ running through it (and of course a lot of it stored in the magnetic field) can certainly harm the circuit, if ...
7
votes
3answers
3k views

Decomposing Kinect Laser Projector - Is it really safe?

I am looking at Kinect Laser and couple of things that are not clear, so I thought I bring up here. First the known facts: - Kinect has a laser projector that works at 840nm - Output power of the ...
5
votes
2answers
2k views

Chassis + Ground Safety

Why is it safer for ground to be connected to the chassis for an electronic system? For example, the ground on the mains supply of an AC motor in a box fan is connected to the outer chassis of the ...
4
votes
3answers
543 views

Is there a wiring design that would protect a person in bath from electrocution when a powered appliance is dropped?

Hairdryer falling into bath is a Hollywood cliche already. Jokes aside, is there a wiring design that would protect a person in this case? Overcurrent protection will trip too late, residual current ...
3
votes
2answers
936 views

How to properly isolate multiple power supplies

Say you have a single 110V AC supply and need to use it for a number of devices, each requiring very different characterists. For me personally these are: a direct use of the 110V AC supply for a ...
8
votes
3answers
2k views

Why is power supply from electrical utility referenced to earth?

In response to the question Basic Training for working with 120V AC zebonaut had replied that "A regular wall outlet is referenced to earth" and this provides the close loop for the circuit to ...
8
votes
8answers
2k views

Basic Training for working with 120V AC

I'm planning to build a digitally-controlled light dimmer circuit. I'm not trained in electrical engineering, and I don't want to do something that an electrician would immediately recognize as ...
1
vote
1answer
266 views

relationship between temperture, current, thickness, and material

I used lan cable for light LED up on my bread board power source is PC's power supply. without any resistor, the lan cable melt! I reallize I have to keep OHM's law in my mind and use proper ...
3
votes
2answers
248 views

cable jacket melts

I am new to hardware. My breadboard just arrived and I am trying to light up my LED. I used computer power supply for power (red wire for + black for -) and used strands of LAN cable for connect LED ...
3
votes
3answers
3k views

Any problems with “floating” an oscilloscope?

I have a Chinese scope with a two-pin power cord and a plastic body, and measure megaohms between its ground terminals and the actual earth, so I believe it has an internal isolation transformer (I ...
0
votes
2answers
358 views

Safe to open old sony remote?

I have an old sony universal remote, the rm-v15. I opened it to get to the pcb, and a strange nasty smell came out of it. Is there anything I should be worried about? Any hazards used in old remotes?
12
votes
3answers
7k views

Extra negative battery cable when charging outside car?

If you go to: http://www.battery-chargers.com/charging_instructions.htm ...Under "Operating Instructions" part "B: Charging battery outside of vehicle", it says you have to attach an extra jumper ...
2
votes
3answers
3k views

Switching 120V AC with Digital Logic on Isolated Power Supply

Context: A digital phase-controlled light dimmer system. 120V AC mains I use an isolating transformer (and rectifying circuit) to generate +12V and +5V DC rails. I want to use reverse phase control (...
17
votes
9answers
6k views

Safety of making PCBs

I've been making a few hobbyist PCBs at home and note that the photoresist developer and ferric chloride etch solutions are both pretty nasty chemicals that come with all kinds of warnings. So I've ...

1
13 14 15 16
17