Questions tagged [single-ended]

An electrical signal composed of a single conductor carrying a voltage which varies with respect to a reference voltage (usually ground), as opposed to a differential signal, which consists of complementary signals carried on each conductor.

15 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
5
votes
1answer
534 views

Charge mode piezoelectric signal conditioning

I have a charge-mode piezoelectric dynamic pressure sensor (datasheet link) that I want to read a signal from. If you look at the datasheet it says the sensor outputs are in a balanced and floating ...
3
votes
0answers
79 views

Noise immunity of single ended analog voltage signal

I want to use a sensor with analog output in my design. The output of the sensor is a low frequency traingular wave (less than 300 Hz) and voltage vetween 0 - 5V. I need to carry the sensor signal to ...
2
votes
1answer
149 views

CAN bus with CANL only?

I'm interfacing a product that operates on a kind of CAN bus. Specifically, it uses the CANL line only. I'd like to use a transceiver I've used before, the MCP2562, and I suspect there's not likely ...
1
vote
0answers
125 views

using the AD8475 as a single ended output

simulate this circuit – Schematic created using CircuitLab I am putting together my schematic and I am trying to figure out if I can use the AD8475 as a single ended output buffer. AD8475 ...
0
votes
1answer
34 views

RF output matching using baluns: LTC6946

The datasheet that I refer to below can be found here: https://www.analog.com/media/en/technical-documentation/data-sheets/6946fb.pdf I have a question about baluns. In the datasheet for LTC6946 ...
0
votes
0answers
57 views

Differential to Single-Ended Converter + Common-mode Shift + Sallen-Key Filter (Is one Stage Possible?)

I have a differential signal that needs to be conditioned as follows: Convert from differential to single-ended. Filter with a 3rd order Sallen-Key filter Common-mode shift into an single-ended, ...
0
votes
0answers
71 views

Current transformers, voltage output vs current output

I'm designing a energy monitoring system that is using split-core clamp current sensors to measure multiple high power lines(40+ lines at 300A each) in a MCB room of a building. I'm currently sourcing ...
0
votes
0answers
41 views

Single ended biopotential amplifier

I have to design a single ended biopotential amplifier circuit based on an already existing model for differential amplifier. In other words, I have a circuit in which each channel has two inputs from ...
0
votes
0answers
195 views

Input and Output Impedances of Differential Amplifier

I have this circuit that is used to convert an incoming analog differential input signal to a single ended signal. The differential input is connected at IN+, IN- and the output is taken from OUT. I ...
0
votes
0answers
149 views

Audio amplifier output bypass capacitor

I'm currently designing a single rail power supply audio amplifier and just wondering what the benifits are (if any) and if its worth including a film/poly capacitor in parallel with the large ...
0
votes
0answers
38 views

Singled ended or Differential - Engine Control Unit

I know this topic has been beaten to death but I still have not got a clear understanding. Pardon me for my bad explanation as I am an automotive engineer by trade. I am simulating an engine knock ...
0
votes
2answers
348 views

How to connect/terminate differential CML logic outputs to single ended ECL logic input?

If I want to use a CML differential gate's (Ex: SY58051AU) output as the enable ECL input for an ECL counter(EX: MC100EP016A), whats the best way to connect the output to input? I think I need to use ...
0
votes
0answers
163 views

How to measure external voltage differential with single ended ADC?

I would like to measure voltages from external circuits with the single ended ADC from an Atmega324. The plan is to power the Atmega324 with 3.3V and use a 1.024 or 2.048 voltage reference. The ...
0
votes
1answer
60 views

Experimenting interference effects for different measurement systems

This is about for low level signals interference/noise being observed with single ended data acquisition inputs but not with diff inputs. Basically there are three data acquisition boards, where one ...
0
votes
0answers
87 views

Will this one-switch resonant topology work?

simulate this circuit – Schematic created using CircuitLab Will this thing work? I do not mind the horrendous amount of interference this may produce. Principle of operation is: Switch-on ...