Questions tagged [to220]
Three-pin PTH package with a heat sink tab for medium power components. Often used for MOSFETs, BJTs and voltage regulators.
22
questions
0
votes
3answers
136 views
How to remove solder mask in Eagle
I want to remove solder mask in particular area for mount a TO220 package.
As shown in below image I want to mount the 7805 using a M3 nut and need to remove solder mask only in covering area. (like ...
1
vote
1answer
58 views
Electrical insulation resistance of TO-220 package with SIL pad and plastic shoulder washer?
What would a ballpark insulation voltage (HI-POT) rating be for a TO-220 package (with a "hot" tab) mounted to a grounded heat-sink with SIL pad and shoulder washer?
I am not seeing much ...
0
votes
2answers
91 views
Intermittent power dissipation calculation on TO-220 package
For a certain application I will be using this resistor. I might also go for this other resistor if needed.
The working conditions are:
Ambient temperature (max): 70 ºC
Power to be dissipated: 15 W
"...
0
votes
1answer
113 views
110V Light in 220V fixture? [closed]
Last year I ordered this lamp, which I received a few weeks later in a rather shadily packaged box sent directly from China. The box had 110V written all over it. I still like the lamp, but we are ...
2
votes
1answer
416 views
Swap FET TO-220 pinout
I messed up my PCB design when I made a change of FET-model. Now the Drain and the Source pins are swapped and it seems that there are no TO-220 models made this way (1-Gate, 2-Source, 3-Drain). Are ...
0
votes
1answer
269 views
Unsolder large TO-220 or TO-247 packages
I'm aware this question may be construed as asking for advice but I'm going to venture to ask anyways. Does anyone have a good method for removing larger TO‑220 or TO‑247 packages? I ...
3
votes
1answer
93 views
Voltage Regulator Heat Concerns
I've read some very good threads here on power and heat dissipation in VRs and believe I understand (most of) it. I have a 5V circuit operating a 12V relay (nominal operating current of 53mA), an ...
0
votes
1answer
954 views
Desoldering a TO-220 MOSFET from a plated through-hole board with SMD complications
I'm planning on replacing a TO-220F package MOSFET on a through-hole circuit board that also has SMD components on it. In this case, an SMD capacitor is connected to the source gate of the MOSFET by ...
5
votes
1answer
754 views
Is there a good reason why TO-220 5-lead components have bent leads?
I've recently acquired some LM2596T-5.0 3A buck converters. They are TO-220-5L packages with bent leads similar to this image:
I have seen other TO-220-5L components with straight leads like this:
...
1
vote
1answer
152 views
Where can I find the C/W rating for PI48, PI49 and PI51 heat sinks?
I was wondering if there is any reference to calculate the C/W ratings for PI48, PI49 and PI51 heat sinks? Just for reference, I am referring to these devices:
http://www.nex-robotics.com/heat-sink....
1
vote
1answer
556 views
Eagle model for TO-220F-4L
Where can I find an Eagle model for the TO-220F-4L package? Or something similar?
I'm trying to add a KA78RXXC-Series Voltage Regulator and I can't even find another component with the same pins.
5
votes
2answers
319 views
TO-220 rectangular washers
The recommended way to mount a TO-220 package is to use a spring clip or bar pressing on the body of device. But the package was designed to be mounted using a bolt through the hole in the heatsink, ...
0
votes
2answers
530 views
Can the metal tab at top of a TO-220 package be cut off?
I am using a TIP120 Darlington transistor in a through-hole (specifically TO-220) package, in a very simple application which does not generate much heat.
I remember reading that the metal tab at the ...
6
votes
5answers
2k views
Does this TO-220 Package Resistor need a heatsink?
I purchased this 0.5 Ohm power resistor, which comes in a TO-220 Package, with the aim of pushing 3A through it (i.e. 4.5W)
The datasheet has the following information:
It says it will rise 6.5 K/W, ...
5
votes
1answer
10k views
What is the difference between TO-220F and TO-220FP cases?
Google search results imply TO-220FP to be full-pack case.
Wikipedia says that TO-220F is full-pack case.
Farnell categorizes TO-220F and TO-22FP differently.
I'm confused. What is the difference ...
4
votes
3answers
692 views
Why do they place a high current device in a low current package?
For instance, it is said that the practical current limit of the TO-220 device is 75A. But I frequently see MOSFET devices for which the specified maximum continuous drain current is above 75A. (...
10
votes
2answers
3k views
Practical current limit for TO-220 package
I see a lot of MOSFET transistors with suprisingly high continuos currents in TO-220 packages. To make matters more magic open ressistance is very low.
For example I want to use IRFB7545PbF N-MOSFET ...
6
votes
3answers
2k views
Heatsink earthing?
I'm currently working on my first circuit that dissipates enough power that I need to use a heatsink. The component in question is a TS1085CZ33 which I'm running with a maximum load of 2.8A ...
4
votes
3answers
2k views
Mains triac safety circuit design
I am investigating using a triac instead of a relay to control 250V 10A devices.
However all the 600V 16A triacs come in TO-220 packages.
According to AS/NZS 3100 and AS/NZS 60335.1 I need at least ...
2
votes
2answers
17k views
What are the pins of a MOSFET in a TO220 package?
I have an IRF3205 MOSFET in a TO-220 package, and I would like to know where the drain, gate and source are. I can't find this information.
4
votes
3answers
12k views
TO-220 case-to-sink thermal resistance
I'm using a KSC1173 TO-220 power transistor in a design, and I need to calculate the case temperature for the maximum average power dissipation, to see if the power dissipation falls under the ...
9
votes
2answers
5k views
What screw should I use to mount a TO220 package?
What screw size should be used to mount a TIP31 in a TO220 package to a bare PCB (no heatsink?) I presume a nut will also be required on the other side, so would appreciate a part number for that too. ...
