User embedded.kyle

44 votes

Accepted

How to improve torque and RPM of a DC motor?

answered Oct 8, 2012 at 17:13

39 votes

Accepted

Why don't we use wireless electricity today?

answered Aug 17, 2012 at 17:52

32 votes

How do I design my very own ARM based processors?

answered Aug 3, 2012 at 19:54

23 votes

Accepted

Testpoints: Vias versus pads

answered Nov 9, 2012 at 13:13

21 votes

Accepted

How to do pulling up or down correctly when interfacing a microSD card?

answered Sep 5, 2012 at 16:07

19 votes

UART & USART - What's the difference

answered Jun 14, 2012 at 17:14

18 votes

Accepted

Control differences between ac induction motor and brushless dc motor?

answered Oct 8, 2012 at 22:05

17 votes

Accepted

Via fences for noise reduction of a chip antenna?

answered Sep 24, 2012 at 20:12

14 votes

Accepted

Cleaning Circuits with Compressed Air

answered Aug 31, 2012 at 17:43

13 votes

Accepted

When to use STD_LOGIC over BIT in VHDL

answered Dec 20, 2012 at 18:41

13 votes

Accepted

For the CAN bus, is it OK to swap CANH and CANL lines?

answered Jun 19, 2013 at 13:35

12 votes

Accepted

how to electrically isolate a PCB from a heat sink

answered Oct 26, 2012 at 15:48

12 votes

Accepted

On high voltage power lines, what is "residual power"?

answered Sep 18, 2012 at 12:54

12 votes

Accepted

Do 3G and phone calls(gsm) use the same antenna in a mobile phone?

answered Jun 24, 2012 at 23:00

11 votes

How do I open a rectangular hole on a metal case?

answered Jun 22, 2012 at 20:07

11 votes

switch debouncing - would toggle switch still bounce

answered Sep 19, 2012 at 12:33

11 votes

Accepted

Why Have Non-Zero Timing on a BLDC?

answered Jan 10, 2013 at 19:31

10 votes

Accepted

Explanation for Differing Stator Winding Orientations

answered Oct 23, 2012 at 19:03

10 votes

Accepted

Why Characteristic Impedance must be 50 ohms?

answered May 10, 2013 at 12:56

9 votes

How to handle unused wire in cable

answered Apr 25, 2013 at 18:13

9 votes

When can FPGA's be used and Microcontrollers/DSPs not?

answered Jan 23, 2014 at 21:30

9 votes

Accepted

What is clock skew, and why can it be negative?

answered Sep 7, 2012 at 13:06

9 votes

Accepted

EEPROM: Same driver for similar chips, different behaviours

answered Jun 20, 2012 at 16:00

8 votes

What happens when an FPGA is powered on and left unconfigured?

answered Jun 22, 2012 at 14:38

8 votes

Controlling small brushless dc motors?

answered Jul 2, 2012 at 14:43

8 votes

Terminology question: does the term "bit-banging" implies not using external signal edge interrupts for timing?

answered Nov 8, 2013 at 14:13

8 votes

Accepted

Are 32-bit ALUs really just 32 1-bit ALUs in parallell?

answered Oct 3, 2012 at 16:22

7 votes

Accepted

How to implement a self tuning PID-like Controller

answered Dec 7, 2012 at 15:24

7 votes

Soldering PCBs directly together

answered Jul 12, 2012 at 17:19

6 votes

Using reset controllers with modern microcontrollers

answered Aug 20, 2012 at 19:34

Stack Exchange Network

135 Answers

How to improve torque and RPM of a DC motor?

Why don't we use wireless electricity today?

How do I design my very own ARM based processors?

Testpoints: Vias versus pads

How to do pulling up or down correctly when interfacing a microSD card?

UART & USART - What's the difference

Control differences between ac induction motor and brushless dc motor?

Via fences for noise reduction of a chip antenna?

Cleaning Circuits with Compressed Air

When to use STD_LOGIC over BIT in VHDL

For the CAN bus, is it OK to swap CANH and CANL lines?

how to electrically isolate a PCB from a heat sink

On high voltage power lines, what is "residual power"?

Do 3G and phone calls(gsm) use the same antenna in a mobile phone?

How do I open a rectangular hole on a metal case?

switch debouncing - would toggle switch still bounce

Why Have Non-Zero Timing on a BLDC?

Explanation for Differing Stator Winding Orientations

Why Characteristic Impedance must be 50 ohms?

How to handle unused wire in cable

When can FPGA's be used and Microcontrollers/DSPs not?

What is clock skew, and why can it be negative?

EEPROM: Same driver for similar chips, different behaviours

What happens when an FPGA is powered on and left unconfigured?

Controlling small brushless dc motors?

Terminology question: does the term "bit-banging" implies not using external signal edge interrupts for timing?

Are 32-bit ALUs really just 32 1-bit ALUs in parallell?

How to implement a self tuning PID-like Controller

Soldering PCBs directly together

Using reset controllers with modern microcontrollers