User JBH

7 votes

Are there two sorts of geometry of JFET?

answered Jul 19, 2021 at 15:57

4 votes

Why are NAND gates used to make AND gates in computers?

answered Sep 8, 2018 at 0:47

3 votes

Grounding in space

answered Feb 17, 2018 at 15:42

3 votes

Is there a fluctuation effect between heat, resistance and current?

answered Jul 3, 2018 at 20:21

3 votes

Help validating MOSFET circuit

answered Aug 12, 2021 at 22:35

3 votes

How can the same radio signal be received by 100s of receivers without any loss in it?

answered Jan 23, 2022 at 22:19

2 votes

Why do we need NMOS transistors for NAND gate?

answered Mar 14, 2021 at 23:48

2 votes

Accepted

How does counter work with xor gate and 3 inputs

answered Sep 7, 2021 at 22:18

2 votes

Can you connect multiple PCBs in series?

answered Jul 26 at 13:31

2 votes

Accepted

Tracking Down a Datasheet for an unknown Optical Sensor

answered Jul 22, 2017 at 14:44

1 vote

Why does boolean algebra in electronics use different notation, and are there advantages to this?

answered Sep 8, 2021 at 0:51

1 vote

Laptop AC adapter power cord

answered Jun 21, 2022 at 5:10

1 vote

Sensor datasheet shows op-amp circuit with capacitor to ground from inverting input. How does this work?

answered Jan 11 at 23:17

1 vote

Is there a mnemonic to remember direction of current flow?

answered Jul 7, 2021 at 6:55

1 vote

For this Art of Electronics circuit, why aren't the transistors specified? And what transistors do I use?

answered Sep 7, 2021 at 21:47

1 vote

Can different manufacturers have same part number for a transistor?

answered Mar 2, 2022 at 5:50

1 vote

Using a 12 V 3 A bilge pump on a 12 V 8.5 A LED power supply

answered Dec 4, 2018 at 16:20

1 vote

Accepted

VHDL Knight Rider

answered Jul 19, 2017 at 8:17

1 vote

Relay component to schematic, are these the same?

answered Jul 20, 2017 at 15:35

1 vote

How to measure RPM from vehicle tires? Wheel Speed Sensor

answered Jul 20, 2017 at 22:15

0 votes

Accepted

Effect of cooling a DC power adapter with too few amps?

answered Jul 21, 2017 at 0:37

0 votes

Turning a high/low signal into a proper digital signal

answered Mar 9, 2022 at 8:04

0 votes

Are there any general "rules of thumb" that one can follow when trying to find equivalent resistances in circuits?

answered Mar 23, 2022 at 6:59

0 votes

How is MOSFET gate resistor chosen?

answered Jun 21, 2022 at 4:59

0 votes

Is there ever any reason to prefer 5% tolerance resistors over 1%?

answered Feb 20 at 23:15

0 votes

Reason not to use aluminium wires, other than higher resistance

answered Jul 26 at 15:30

0 votes

Do any power loads require both power lines disconnected by the "off" switch?

answered Oct 1 at 19:53

Stack Exchange Network

27 Answers

Are there two sorts of geometry of JFET?

Why are NAND gates used to make AND gates in computers?

Grounding in space

Is there a fluctuation effect between heat, resistance and current?

Help validating MOSFET circuit

How can the same radio signal be received by 100s of receivers without any loss in it?

Why do we need NMOS transistors for NAND gate?

How does counter work with xor gate and 3 inputs

Can you connect multiple PCBs in series?

Tracking Down a Datasheet for an unknown Optical Sensor

Why does boolean algebra in electronics use different notation, and are there advantages to this?

Laptop AC adapter power cord

Sensor datasheet shows op-amp circuit with capacitor to ground from inverting input. How does this work?

Is there a mnemonic to remember direction of current flow?

For this Art of Electronics circuit, why aren't the transistors specified? And what transistors do I use?

Can different manufacturers have same part number for a transistor?

Using a 12 V 3 A bilge pump on a 12 V 8.5 A LED power supply

VHDL Knight Rider

Relay component to schematic, are these the same?

How to measure RPM from vehicle tires? Wheel Speed Sensor

Effect of cooling a DC power adapter with too few amps?

Turning a high/low signal into a proper digital signal

Are there any general "rules of thumb" that one can follow when trying to find equivalent resistances in circuits?

How is MOSFET gate resistor chosen?

Is there ever any reason to prefer 5% tolerance resistors over 1%?

Reason not to use aluminium wires, other than higher resistance

Do any power loads require both power lines disconnected by the "off" switch?