User VirtApp

12 votes

2 answers

998 views

How does this overvoltage protection work?

asked Jan 2, 2021 at 13:46

9 votes

4 answers

1k views

ATmega328P reading DIP switches using the lowest possible power

asked Jul 1, 2021 at 15:11

5 votes

8 answers

5k views

Cost effective way to protect circuit from overvoltage

asked Aug 12, 2020 at 10:42

4 votes

2 answers

841 views

MCU working at 3.3V and RS485 driver at 5V - how does this circuit work?

asked Apr 15, 2022 at 12:58

2 votes

0 answers

100 views

Arduino UARTS Auto addressing slaves

asked May 29, 2020 at 17:03

2 votes

1 answer

155 views

Detecting cut wire (tampering) for low power project

asked Jan 3, 2022 at 16:18

2 votes

1 answer

397 views

Step up 3.3V to 5V to use as power of op-amp

asked Feb 20, 2021 at 9:20

2 votes

2 answers

1k views

Linearizing a 0-10V non linear sensor

asked Dec 17, 2018 at 19:52

1 vote

1 answer

432 views

Overvoltage protection for DC controlled Device

asked Dec 18, 2020 at 13:40

1 vote

3 answers

795 views

Crowbar circuit design: choosing the correct parts

asked Dec 19, 2020 at 11:03

1 vote

3 answers

189 views

TLP184 Optocoupler - Something is going wrong

asked Aug 17, 2020 at 8:12

1 vote

0 answers

54 views

Noise suppress recommendation and best practices

asked Mar 19, 2020 at 22:21

1 vote

2 answers

1k views

POE Extraction and port reuse for POE Device

asked Apr 8, 2020 at 17:35

1 vote

1 answer

482 views

Analog input to ATMEGA328P using op-amp - how does this circuit work?

asked Feb 15, 2021 at 19:25

1 vote

1 answer

152 views

333mV Current transducer - how to read it and protect the Atmega328p input

asked Jan 18, 2022 at 21:46

0 votes

1 answer

280 views

Pi-matching impedance calculation for LoRa 868Mhz RFM95

asked Jun 1, 2022 at 10:13

0 votes

0 answers

258 views

Hardware watchdog for my ESP32 Board - circuit and design suggestion

asked Jun 3, 2022 at 8:31

0 votes

1 answer

85 views

How can I regulate 220 Vac fans with a microcontroller?

asked Aug 4, 2022 at 14:41

0 votes

0 answers

40 views

Drive 50 SPI oled displays with a single ESP32

asked Apr 9, 2020 at 15:24

0 votes

2 answers

256 views

Effective differences between MAX485EESA+T and MAX485ESA+T?

asked May 8, 2020 at 21:23

0 votes

1 answer

731 views

ADM2483 or MAX485 Design: Modbus RS485 RTU bus in harsh environment

asked May 22, 2020 at 17:29

0 votes

0 answers

28 views

Sequential access of 1-Wire devices

asked May 28, 2020 at 9:26

0 votes

1 answer

111 views

RS485 over CAN: when and why?

asked Sep 21, 2020 at 17:35

0 votes

3 answers

264 views

Step down 9-36V to 5V: Best and cheap way to power a Raspberry Pi

asked Sep 25, 2020 at 7:20

0 votes

1 answer

53 views

MCU - Two power input: from PoE and DC 12V Switch between them

asked Dec 11, 2020 at 13:51

0 votes

2 answers

79 views

Mosfet load control - different design compared

asked May 30, 2020 at 9:48

0 votes

1 answer

956 views

Multidrop RS232 - Diode selection and doubts

asked Jun 16, 2020 at 18:15

0 votes

1 answer

956 views

Switch "On"/"Off" RS485 data lines

asked Jun 19, 2020 at 14:37

0 votes

0 answers

51 views

RS485 Trancievers: ADM2483 VS ISO15

asked Jun 27, 2020 at 12:48

0 votes

1 answer

371 views

Troubleshooting I2C issues of ESP32-POE-ISO with LAN

asked Jul 26, 2020 at 17:58

Stack Exchange Network

44 Questions

How does this overvoltage protection work?

ATmega328P reading DIP switches using the lowest possible power

Cost effective way to protect circuit from overvoltage

MCU working at 3.3V and RS485 driver at 5V - how does this circuit work?

Arduino UARTS Auto addressing slaves

Detecting cut wire (tampering) for low power project

Step up 3.3V to 5V to use as power of op-amp

Linearizing a 0-10V non linear sensor

Overvoltage protection for DC controlled Device

Crowbar circuit design: choosing the correct parts

TLP184 Optocoupler - Something is going wrong

Noise suppress recommendation and best practices

POE Extraction and port reuse for POE Device

Analog input to ATMEGA328P using op-amp - how does this circuit work?

333mV Current transducer - how to read it and protect the Atmega328p input

Pi-matching impedance calculation for LoRa 868Mhz RFM95

Hardware watchdog for my ESP32 Board - circuit and design suggestion

How can I regulate 220 Vac fans with a microcontroller?

Drive 50 SPI oled displays with a single ESP32

Effective differences between MAX485EESA+T and MAX485ESA+T?

ADM2483 or MAX485 Design: Modbus RS485 RTU bus in harsh environment

Sequential access of 1-Wire devices

RS485 over CAN: when and why?

Step down 9-36V to 5V: Best and cheap way to power a Raspberry Pi

MCU - Two power input: from PoE and DC 12V Switch between them

Mosfet load control - different design compared

Multidrop RS232 - Diode selection and doubts

Switch "On"/"Off" RS485 data lines

RS485 Trancievers: ADM2483 VS ISO15

Troubleshooting I2C issues of ESP32-POE-ISO with LAN