Skip to main content
Dynamic_equilibrium's user avatar
Dynamic_equilibrium's user avatar
Dynamic_equilibrium's user avatar
Dynamic_equilibrium
  • Member for 10 years, 9 months
  • Last seen this week
13 votes
7 answers
11k views

Via in PCB - Why not go for a solid copper filled via than a plated via?

11 votes
4 answers
2k views

How does this PNP transistor improve the switching performance of MOSFET?

7 votes
4 answers
1k views

Why is increasing gate voltage beyond 'reasonable' limits not advantageous in power MOSFETs?

7 votes
3 answers
1k views

How do I explain this regulation action in terms of control theory?

6 votes
4 answers
3k views

Can different manufacturers have same part number for a transistor?

6 votes
3 answers
931 views

Why is the Base-emitter ON voltage as high as 2V in the BJT datasheet?

6 votes
2 answers
1k views

Why is the telecom input power supply range 36 to 72 V (polarity ignored)?

6 votes
2 answers
1k views

Why is the thermal resistance of copper shown higher than FR4 in below snap?

6 votes
3 answers
1k views

Does an EEPROM consume power only during the transition edges or during entire read/write cycle?

6 votes
3 answers
5k views

Why is phase margin considered more important than gain margin in dc-dc converters?

5 votes
4 answers
672 views

From a flux point of view, how can we explain that the equivalent inductance is half when identical inductors are connected in parallel?

5 votes
2 answers
1k views

What is the purpose of this sense pin in dual MOSFET package? [duplicate]

5 votes
1 answer
211 views

What is the purpose of voids near thermal pad in a MOSFET?

5 votes
3 answers
1k views

For below circuit, the simulation result is not matching with theoretical prediction

5 votes
3 answers
714 views

What is the meaning of the following statement regarding Zener diode addition at the output of a voltage regulator?

5 votes
3 answers
938 views

Does turn-on and turn-off delay cause MOSFET switching loss?

5 votes
1 answer
646 views

Why is the Y-capacitor named so?

4 votes
5 answers
2k views

Do we really need the metallic chassis to be grounded if it is coated with a non-conductive paint?

4 votes
1 answer
122 views

What is meant by Switching charge ( under Gate charge characteristics) in the given MOSFET datasheet?

4 votes
1 answer
470 views

Power converter: Why is audio susceptibility named so?

4 votes
3 answers
441 views

Frequency analyzer for loop gain measurement - Why should the injection point have low output impedance and high input impedance?

4 votes
1 answer
480 views

What is meant by the statement "Local bypass capacitors are needed to control EMC coupling with heat sink"?

4 votes
3 answers
4k views

Why are differential mode chokes (inductors) not generally coupled?

4 votes
2 answers
3k views

How do we appropriately select the duty cycle in a flyback converter?

4 votes
1 answer
2k views

Why is buck-boost converter showing a different trend than buck and boost in efficiency peaking point?

3 votes
1 answer
576 views

Why is the thermal conductivity of FR4 shown to have two different values? (Based on heat flow direction)

3 votes
4 answers
848 views

How does the bottom resistor in feedback resistive divider impact noise sensitivity?

3 votes
1 answer
1k views

Why do they keep series resistor with each open drain output during Wired OR logic?

3 votes
3 answers
11k views

Why is saturation region called so in BJT characteristics?

3 votes
1 answer
4k views

What is meant by soft strap and pin strap (HW strap) in a processor datasheet?

1
2 3 4 5 6