User apalopohapa

55 votes

What is an LUT in FPGA?

answered May 8, 2015 at 8:04

23 votes

Accepted

Op Amp gain less than 1?

answered Nov 20, 2013 at 3:57

19 votes

Accepted

Which has better efficiency: step-up or step-down switching voltage regulator?

answered Sep 30, 2013 at 17:34

17 votes

Accepted

Altium layers "blacked out"

answered Nov 28, 2013 at 4:09

15 votes

Accepted

Conditional stability

answered Jun 16, 2013 at 10:59

13 votes

Accepted

A decent library of component simulation, schematic and PCB layout?

answered Nov 14, 2012 at 22:52

12 votes

Accepted

Why would you attach a Diode to the base of a BJT?

answered Nov 17, 2012 at 1:26

12 votes

Why is Floating point non-synthesizable in verilog

answered Oct 18, 2013 at 6:24

12 votes

Accepted

Does this circuit regulate current?

answered Jun 1, 2014 at 10:24

10 votes

Accepted

Why is my instrumentation amplifier's gain non-linear?

answered Dec 28, 2012 at 12:17

9 votes

Accepted

What is the best tool to hold small printed circuit board?

answered Nov 8, 2013 at 20:37

8 votes

Accepted

Controlling MSP430 PWM with a Laptop

answered Mar 8, 2013 at 9:17

8 votes

Run code once in lifetime of an embedded C program

answered Apr 11, 2016 at 7:41

7 votes

Accepted

Logic NOT gate only works with Oscilloscope probe connected

answered Mar 13, 2013 at 6:12

7 votes

Number of gates in series

answered Jan 6, 2013 at 7:29

7 votes

Reasoning behind "neutral pin nearest the edge" rule of thumb?

answered Nov 9, 2012 at 9:30

7 votes

Accepted

Why is it ok to use polarized caps to remove DC offset from an audio input?

answered Apr 12, 2010 at 17:42

6 votes

Accepted

MCP3008 ADC , Reading 16 bits instead of 10 bits

answered Jan 23, 2013 at 0:47

6 votes

Bootstrap circuit function

answered Feb 22, 2013 at 20:40

6 votes

How can I make a plated-through hole in Eagle?

answered Dec 5, 2012 at 8:37

6 votes

Accepted

How does writing to output pins on PORTB affect RBIF interrupt on PIC16F877

answered Jan 11, 2013 at 18:50

6 votes

Proper clock generation for VHDL testbenches

answered Jan 11, 2015 at 10:05

5 votes

How to get a FPGA design that will definitely work on actual hardware

answered Mar 2, 2016 at 11:40

5 votes

Accepted

Is it valid to consider back-EMF in a DC motor equivalent to increased inductance?

answered Jan 12, 2013 at 4:52

5 votes

VHDL code compiling on quartus II

answered Jan 13, 2013 at 13:38

5 votes

Accepted

MOSFET and clamp on I2C interface lines as level tranlastor

answered Jan 14, 2013 at 5:32

5 votes

Why do batteries with the same voltage have different currents?

answered Nov 30, 2012 at 1:28

5 votes

Accepted

(How) can I run a microcontroller and DC motor from the same battery?

answered Mar 25, 2013 at 0:57

5 votes

Accepted

Eagle: Removing unwanted bits of copper pour

answered Mar 4, 2013 at 18:19

5 votes

Accepted

Set toggle rate in Quartus II

answered Jan 22, 2013 at 19:25

Stack Exchange Network

167 Answers

What is an LUT in FPGA?

Op Amp gain less than 1?

Which has better efficiency: step-up or step-down switching voltage regulator?

Altium layers "blacked out"

Conditional stability

A decent library of component simulation, schematic and PCB layout?

Why would you attach a Diode to the base of a BJT?

Why is Floating point non-synthesizable in verilog

Does this circuit regulate current?

Why is my instrumentation amplifier's gain non-linear?

What is the best tool to hold small printed circuit board?

Controlling MSP430 PWM with a Laptop

Run code once in lifetime of an embedded C program

Logic NOT gate only works with Oscilloscope probe connected

Number of gates in series

Reasoning behind "neutral pin nearest the edge" rule of thumb?

Why is it ok to use polarized caps to remove DC offset from an audio input?

MCP3008 ADC , Reading 16 bits instead of 10 bits

Bootstrap circuit function

How can I make a plated-through hole in Eagle?

How does writing to output pins on PORTB affect RBIF interrupt on PIC16F877

Proper clock generation for VHDL testbenches

How to get a FPGA design that will definitely work on actual hardware

Is it valid to consider back-EMF in a DC motor equivalent to increased inductance?

VHDL code compiling on quartus II

MOSFET and clamp on I2C interface lines as level tranlastor

Why do batteries with the same voltage have different currents?

(How) can I run a microcontroller and DC motor from the same battery?

Eagle: Removing unwanted bits of copper pour

Set toggle rate in Quartus II