User user135172

22 votes

10 answers

7k views

Why do I need a ground when simulating a circuit? I thought voltage was relative between two nodes!

asked Dec 6, 2017 at 12:42

7 votes

2 answers

1k views

How can I deduce the power of a capacitor from its datasheet?

asked Feb 24, 2019 at 9:52

7 votes

3 answers

214 views

How to reduce an audio system noise in a way which is similar to a human touching one of the system's components?

asked Jul 25, 2019 at 14:40

3 votes

1 answer

1k views

A recommended way to check a transistor is not burned, without burning other PCB parts

asked Jun 3, 2019 at 16:08

3 votes

2 answers

132 views

How to extract minimum supply voltage from the datasheets

asked May 17, 2019 at 11:43

1 vote

2 answers

793 views

Is the following op-amp-circuit-in-the-Laplace-domain analysis correct?

asked May 22, 2019 at 6:20

1 vote

2 answers

150 views

L298 data sheet

asked Apr 14, 2018 at 12:44

1 vote

0 answers

52 views

The equivalent circuit for \$V_{in} > 0\$ with the amplitude of \$V_{out}\$

asked Jul 23, 2015 at 11:11

1 vote

2 answers

4k views

How to calculate the exact delay of a delayed ON/OFF imlemented by low pass filter

asked Apr 29, 2018 at 13:36

1 vote

6 answers

317 views

A weird question about the cutoff point of an RC low pass filter

asked Apr 30, 2018 at 18:09

1 vote

3 answers

219 views

Low pas filter time constant for a square input

asked May 7, 2018 at 9:39

1 vote

2 answers

3k views

How to calculate, for a square wave input, the cut-off frequency point for a basic RC low pass filter with

asked May 14, 2018 at 14:31

0 votes

2 answers

201 views

How to calculate properties of voltage regulation circuits [duplicate]

asked May 7, 2018 at 9:48

0 votes

2 answers

80 views

What is the purpose of the series of actions: amplification, band-pass, rectification, and low-pass?

asked Nov 7, 2017 at 16:58

0 votes

2 answers

617 views

How to understand the parameters of a transistor [closed]

asked Dec 20, 2017 at 12:35

0 votes

1 answer

65 views

bidirecttional arduino-controlled motor. What do we need the diodes for?

asked Mar 20, 2018 at 13:44

0 votes

2 answers

538 views

How to change component size in expressSCH?

asked Apr 16, 2018 at 10:22

0 votes

2 answers

108 views

How to design mechanical switches to an arduino controlled circuit

asked Apr 16, 2018 at 13:29

0 votes

0 answers

79 views

What is the Thevenin Norton equivalent of the folloing circuit

asked Mar 14, 2019 at 16:40

0 votes

1 answer

93 views

What is the advantage of concatenating two nMOSFETs M1,M2 with Source of M1 connected to Gate of M2?

asked May 30, 2019 at 8:42

0 votes

2 answers

487 views

How do I refer the transfer function of a system from its Laplace equivalent?

asked May 30, 2019 at 8:51

0 votes

1 answer

2k views

What is the meaning of "The transistors Q1,Q2 are identical" and of "Q1/Q2 = 10"

asked Jun 3, 2019 at 14:24

Stack Exchange Network

22 Questions

Why do I need a ground when simulating a circuit? I thought voltage was relative between two nodes!

How can I deduce the power of a capacitor from its datasheet?

How to reduce an audio system noise in a way which is similar to a human touching one of the system's components?

A recommended way to check a transistor is not burned, without burning other PCB parts

How to extract minimum supply voltage from the datasheets

Is the following op-amp-circuit-in-the-Laplace-domain analysis correct?

L298 data sheet

The equivalent circuit for \$V_{in} > 0\$ with the amplitude of \$V_{out}\$

How to calculate the exact delay of a delayed ON/OFF imlemented by low pass filter

A weird question about the cutoff point of an RC low pass filter

Low pas filter time constant for a square input

How to calculate, for a square wave input, the cut-off frequency point for a basic RC low pass filter with

How to calculate properties of voltage regulation circuits [duplicate]

What is the purpose of the series of actions: amplification, band-pass, rectification, and low-pass?

How to understand the parameters of a transistor [closed]

bidirecttional arduino-controlled motor. What do we need the diodes for?

How to change component size in expressSCH?

How to design mechanical switches to an arduino controlled circuit

What is the Thevenin Norton equivalent of the folloing circuit

What is the advantage of concatenating two nMOSFETs M1,M2 with Source of M1 connected to Gate of M2?

How do I refer the transfer function of a system from its Laplace equivalent?

What is the meaning of "The transistors Q1,Q2 are identical" and of "Q1/Q2 = 10"