User Houston Fortney

16 votes

Multitasking on PIC microcontrollers

answered Oct 7, 2015 at 9:51

14 votes

Accepted

What is the purpose of the sharp edges (aka mouse bites, aka perforated breakaway tabs) on the PCB?

answered Oct 3, 2015 at 11:43

13 votes

Accepted

Resistance of an LED in a simple battery-resistor-LED circuit?

answered Oct 7, 2015 at 0:02

11 votes

Step-by-step explanation of how voltage follower reaches steady state using negative feedback

answered Sep 18, 2015 at 23:16

9 votes

What's the schematic to share one crystal with two micros?

answered Aug 27, 2015 at 21:34

6 votes

Accepted

How to connect these pads

answered Aug 21, 2015 at 20:22

6 votes

Accepted

Single bit of memory

answered Aug 17, 2015 at 21:42

6 votes

How to make 1 bit permanent memory circuit?

answered Sep 1, 2015 at 19:50

6 votes

What is the correct way to measure voltage with an optocoupler?

answered Oct 5, 2015 at 2:55

6 votes

Can I place a relay at the output pin of a 555-timer

answered Nov 3, 2017 at 3:24

5 votes

Accepted

Hall effect sensor operational distance from magnet

answered Aug 23, 2015 at 23:32

4 votes

Detect 3.5mm stereo jack plugged in

answered Aug 30, 2015 at 16:24

4 votes

If adding resistors in parallel decreases total resistance, why doesn't the voltage in the circuit change?

answered Aug 30, 2015 at 20:11

4 votes

What is the purpose of a pull-up resistor in a microcontroller?

answered Aug 16, 2015 at 16:23

4 votes

Accepted

Solving for \$v_{out}\$ in this circuit

answered Oct 9, 2015 at 0:14

3 votes

Accepted

Keeping power on a capacitor after its charged?

answered Oct 6, 2015 at 0:11

3 votes

Bridge rectifier homework

answered Oct 6, 2015 at 22:01

3 votes

How can I amplify my transmitter's RF signal to open the garage from the 12th floor?

answered Aug 31, 2015 at 18:53

3 votes

Amplify Pizzo Buzzer

answered Sep 2, 2015 at 0:26

3 votes

Accepted

Designing logic for 7-segment display

answered Sep 26, 2015 at 12:08

3 votes

Accepted

How an electrical component behave after being exposed to excessive current/voltage?

answered Aug 16, 2015 at 14:37

3 votes

Accepted

How do I program an Atmel SAM in the field?

answered Aug 18, 2015 at 10:45

3 votes

Accepted

STM32: Timer Modes

answered Aug 30, 2015 at 16:52

3 votes

A practical integrator that does not behave like a low-pass filter?

answered Aug 25, 2015 at 23:29

2 votes

Driving MOSFET gate using PIC

answered Aug 30, 2015 at 14:53

2 votes

Calibrating the output voltage 3

answered Aug 22, 2015 at 17:10

2 votes

Switch that is physically closed, and electrically opened

answered Aug 25, 2015 at 11:08

2 votes

Arduino digital input - Read voltage slightly higher then 5V - a power efficient solution

answered Aug 15, 2015 at 19:44

2 votes

Charging and discharging of a capacitor experiment

answered Sep 10, 2015 at 9:22

2 votes

toggle 12v as high and 11v as low for arduino

answered Sep 14, 2015 at 11:12

Stack Exchange Network

78 Answers

Multitasking on PIC microcontrollers

What is the purpose of the sharp edges (aka mouse bites, aka perforated breakaway tabs) on the PCB?

Resistance of an LED in a simple battery-resistor-LED circuit?

Step-by-step explanation of how voltage follower reaches steady state using negative feedback

What's the schematic to share one crystal with two micros?

How to connect these pads

Single bit of memory

How to make 1 bit permanent memory circuit?

What is the correct way to measure voltage with an optocoupler?

Can I place a relay at the output pin of a 555-timer

Hall effect sensor operational distance from magnet

Detect 3.5mm stereo jack plugged in

If adding resistors in parallel decreases total resistance, why doesn't the voltage in the circuit change?

What is the purpose of a pull-up resistor in a microcontroller?

Solving for \$v_{out}\$ in this circuit

Keeping power on a capacitor after its charged?

Bridge rectifier homework

How can I amplify my transmitter's RF signal to open the garage from the 12th floor?

Amplify Pizzo Buzzer

Designing logic for 7-segment display

How an electrical component behave after being exposed to excessive current/voltage?

How do I program an Atmel SAM in the field?

STM32: Timer Modes

A practical integrator that does not behave like a low-pass filter?

Driving MOSFET gate using PIC

Calibrating the output voltage 3

Switch that is physically closed, and electrically opened

Arduino digital input - Read voltage slightly higher then 5V - a power efficient solution

Charging and discharging of a capacitor experiment

toggle 12v as high and 11v as low for arduino