Return to Question

I have no background in electrical engineering other than curiosity; I'm more of a copycat. I have been trying to reproduce this schematic:

I have searched the forum but don't see anything remotely close to what I am doing.

I have built it as per the schematic. I did add an LED to pin 7 of the LM311 as an indicator the signal is working (one thing of note: I can only get a signal on output if I press the "normally open" momentary button).

I am feeding the audio through a BT module. When I scope the output I do get a reading:

I have no idea if it's correct. I never used a scope before.

When pin 7 of the comparator is connected to the reset pin of the 555 I should get a polyphonic square wave (I believe) from pin 3, which drives a BC327 transistor which will in turn operate the gate of an IRFP260 MOSFET

The two red LEDs tell me the 555 and the BC327 are both outputting power constantly. They should both be flashing if the reset pin is being triggered properly. I don't know if I need a pulldown resistor on pin 4 or if my output from pin 7 is not switching to low as I understand it should. Any help is appreciated.

Here's a link to the finished project: https://youtu.be/DBukpYea4mQ

I have no background in electrical engineering other than curiosity; I'm more of a copycat. I have been trying to reproduce this schematic:

I have searched the forum but don't see anything remotely close to what I am doing.

I have built it as per the schematic. I did add an LED to pin 7 of the LM311 as an indicator the signal is working (one thing of note: I can only get a signal on output if I press the "normally open" momentary button).

I am feeding the audio through a BT module. When I scope the output I do get a reading:

I have no idea if it's correct. I never used a scope before.

When pin 7 of the comparator is connected to the reset pin of the 555 I should get a polyphonic square wave (I believe) from pin 3, which drives a BC327 transistor which will in turn operate the gate of an IRFP260 MOSFET.

The two red LEDs tell me the 555 and the BC327 are both outputting power constantly. They should both be flashing if the reset pin is being triggered properly. I don't know if I need a pulldown resistor on pin 4 or if my output from pin 7 is not switching to low as I understand it should. Any help is appreciated.

Here's a link to the finished project: https://youtu.be/DBukpYea4mQ

First post here please be kind. I have no background in electrical engineering other than curiosity; I'm more of a copycat. I have been trying to reproduce this schematic:

]2

I have searched the forum but don't see anything remotely close to what I am doing.

I have built it as per the schematic. I did add an LED to pin 7 of the LM311 as an indicator the signal is working (one thing of note: I can only get a signal on output if I press the "normally open" momentary button).

I am feeding the audio through a BT module. When I scope the output I do get a reading:

]3

I have no idea if it's correct. I never used a scope before.

When pin 7 of the comparator is connected to the reset pin of the 555 I should get a polyphonic square wave (I believe) from pin 3, which drives a BC327 transistor which will in turn operate the gate of an IRFP260 MOSFET

]4

The two red LEDs tell me the 555 and the BC327 are both outputting power constantly. They should both be flashing if the reset pin is being triggered properly. I don't know if I need a pulldown resistor on pin 4 or if my output from pin 7 is not switching to low as I understand it should. Any help is appreciated.

Here's a link to the finished project: https://youtu.be/DBukpYea4mQ

I have no background in electrical engineering other than curiosity; I'm more of a copycat. I have been trying to reproduce this schematic:

I have searched the forum but don't see anything remotely close to what I am doing.

I have built it as per the schematic. I did add an LED to pin 7 of the LM311 as an indicator the signal is working (one thing of note: I can only get a signal on output if I press the "normally open" momentary button).

I am feeding the audio through a BT module. When I scope the output I do get a reading:

I have no idea if it's correct. I never used a scope before.

When pin 7 of the comparator is connected to the reset pin of the 555 I should get a polyphonic square wave (I believe) from pin 3, which drives a BC327 transistor which will in turn operate the gate of an IRFP260 MOSFET

The two red LEDs tell me the 555 and the BC327 are both outputting power constantly. They should both be flashing if the reset pin is being triggered properly. I don't know if I need a pulldown resistor on pin 4 or if my output from pin 7 is not switching to low as I understand it should. Any help is appreciated.

Here's a link to the finished project: https://youtu.be/DBukpYea4mQ

First post here please be kind. I have no background in electrical engineering other than curiosity. I'm more of a copycat. I have been trying to reproduce this schematic,]   I have searched the forum but don't see anything remotely close to what I am doing. I have built it as per the schematic. I did add an LED to pin 7 of the LM311 as an indicator the signal is working. (One thing of note, I can only get a signal on output if I press the "normally open" momentary button) I am feeding the audio through a BT module. When I scope the output I do get a reading. (I have no idea if it's correct. I never used a scope before.) When pin 7 of the comparator is connected to reset of the 555 I should get a polyphonic square wave (I believe) from pin 3, which drives a BC327 transistor which will in turn operate the gate of an irfp260 MOSFET the 2 red LEDs tell me the 555 and the BC327 are both outputting power constantly. They should both be flashing if the reset pin was being triggered properly. I don't know if I need a pulldown resistor on pin 4 or if my output from pin 7 is not switching to low as I understand it should. Any help is appreciated. I am incredibly new to oscilloscopes and am slowly learning how to use them.

Here's a link to the finished project.

https://youtu.be/DBukpYea4mQ

First post here please be kind. I have no background in electrical engineering other than curiosity; I'm more of a copycat. I have been trying to reproduce this schematic:

]2

I have searched the forum but don't see anything remotely close to what I am doing.

I have built it as per the schematic. I did add an LED to pin 7 of the LM311 as an indicator the signal is working (one thing of note: I can only get a signal on output if I press the "normally open" momentary button).

I am feeding the audio through a BT module. When I scope the output I do get a reading:

]3

I have no idea if it's correct. I never used a scope before. 

When pin 7 of the comparator is connected to the reset pin of the 555 I should get a polyphonic square wave (I believe) from pin 3, which drives a BC327 transistor which will in turn operate the gate of an IRFP260 MOSFET

]4

The two red LEDs tell me the 555 and the BC327 are both outputting power constantly. They should both be flashing if the reset pin is being triggered properly. I don't know if I need a pulldown resistor on pin 4 or if my output from pin 7 is not switching to low as I understand it should. Any help is appreciated.

Here's a link to the finished project: https://youtu.be/DBukpYea4mQ