12
\$\begingroup\$

Can I use an AC power adapter that can be connected through USB port? My board is Arduino Uno and usually connect to my computer through the USB cable.

AC power adapter <-> USB port <-(USB cable)-> Arduino USB port

What kinds of components can be used as external power supply for Arduino board? It's really nice if you have some images or names about them.

\$\endgroup\$
5
  • 1
    \$\begingroup\$ Why shouldn't it be good? As long as the voltage and current is the same, there's no difference if it's generated by a PC or a converter... \$\endgroup\$
    – clabacchio
    Commented Jan 24, 2012 at 10:39
  • \$\begingroup\$ Aside from cost, why not hook up several 9V in parallel to power the board? \$\endgroup\$
    – user10874
    Commented Jul 15, 2012 at 19:08
  • \$\begingroup\$ electronics.stackexchange.com/questions/17987/… You can also use the Vin pin if you do not want to use a power jack... for example a battery with a clip would work. \$\endgroup\$
    – NickHalden
    Commented Jun 3, 2013 at 20:33
  • \$\begingroup\$ Surely this is spelled out in the documentation of the arduino!? \$\endgroup\$
    – Olin Lathrop
    Commented Jun 3, 2013 at 21:10
  • \$\begingroup\$ AC power adapter that can be connected through USB port I would not recommend putting a 12V adaptor 'on' your USB port. \$\endgroup\$
    – aaa
    Commented Apr 2, 2015 at 12:02

4 Answers 4

Reset to default
20
\$\begingroup\$

An Arduino Uno can be powered by

  • a stable (regulated) 5V DC, which you can either supply via the USB power lines, or via the shield connectors, or
  • an unregulated 6-20 V DC (7-12V recommended), which you can supply via the 2.1 mm centre-positive barrel plug connector.

I would not recommend using a 9V battery, because its voltage will drop quickly, but in a pinch this can be used.

ref: http://arduino.cc/en/Main/ArduinoBoardUno

\$\endgroup\$
3
  • \$\begingroup\$ do you have some images as example? I'm pretty much newbie at this stuff. \$\endgroup\$
    – Pete Houston
    Commented Jan 25, 2012 at 5:39
  • \$\begingroup\$ What about the maximum allowed current? can i use 12V-1500MA adapter? and also would it be ok if i connect the USB cable while the adapter is plugged in? \$\endgroup\$
    – razzak
    Commented May 13, 2015 at 18:55
  • \$\begingroup\$ 12V/1.5A should be OK, but the things you connect to the arduino should not draw too much current. A couple of LEDs will be totally OK. Plugging both USB and external power is not a good idea, the USB could be back-powered. \$\endgroup\$
    – Wouter van Ooijen
    Commented May 13, 2015 at 19:19
6
\$\begingroup\$

The answer is 6-20V (7-16V recommended). http://arduino.cc/en/Main/arduinoBoardUno

\$\endgroup\$
1
  • \$\begingroup\$ Yep. I use a 5v regulated myself. \$\endgroup\$
    – mikeY
    Commented Jun 3, 2013 at 22:39
4
\$\begingroup\$

Yes, you could use a USB battery device or USB charger or a 9V battery clip with a 2.1mm DC power plug.

\$\endgroup\$
3
  • \$\begingroup\$ Why Wouter van Ooijen doesn't recommend 9V battery and you do? \$\endgroup\$
    – Pete Houston
    Commented Jan 25, 2012 at 5:40
  • \$\begingroup\$ I included why I don't recommend a 9V battery. Hence you can infer that Hellonearthis gives less weigth to that argument. Conclude for yourself whether it is relevant in your case. \$\endgroup\$
    – Wouter van Ooijen
    Commented Jan 25, 2012 at 8:16
  • \$\begingroup\$ This is what I use broken cell phone chargers for. BTW it's that hello near ths? Or hell on earth is? \$\endgroup\$
    – user23736
    Commented May 9, 2013 at 22:25
2
\$\begingroup\$

Can i use 12V-1500MA adapter?

Since no-one mentioned this: I believe the arduino uses a linear regulator. This converts the input voltage down to 5V by burning the excess power as heat.

For example, if you supply it with 12V and the arduino draws 100mA on the 5V supply, then the regulator will have 12-5=7V dropout, and it will dissipate 7V*0.1A = 0.7W.

Since it is usually a small SMD device, not fitted with a heat sink, it can't dissipate a lot of power. It will overheat very easily if you draw high current.

Thus if you feed it with 12V the limit will not be the supply current (unless your supply is really wimpy) but the onboard regulator dissipation.

This does not apply if you use a 5V supply, like a 2A cellphone charger, although some components on the board, like the ferrite beads on the +5V line, may object to such high currents.

Anyway, if you want to do high current stuff like servos, motors, long LED strips and the like, power them separately from the supply, and definitely not from the arduino itself. The arduino should control your stuff, light a few LEDs for indication, total maybe 100mA, but it is not designed for power.

\$\endgroup\$

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.