Questions tagged [enc28j60]
ENC28J60 is a SPI-interfaced 10Mbit Ethernet controller with MAC and PHY. It's popular with hobbyists and there are many breakout boards and software libraries for it.
11 questions with no upvoted or accepted answers
4
votes
0
answers
464
views
Linux enc28j60 driver always times out on transmit
I've wired up an ENC28J60 module with an SPI interface to a Beaglebone Black development board running Linux 3.8, but I cannot get the device to TX (or RX) anything. Every attempt to TX times out and ...
- 217
4
votes
0
answers
5k
views
How to get an ENC28J60 to work?
For starters: Yes I know I'm about to reinvent the wheel with the following task ahead.
I want to create my own library for the ENC28J60 for an AVR (ATMEGA1284P).
So I've been browsing the net for ...
- 81
3
votes
1
answer
108
views
LDO voltage regulator malfunctioning as passthrough after 24/7 usage
I have designed a custom pcb utilizing the ENC28J60 ethernet chip. The board has 5V in which powers both the ENC28J60 (through a AMS1117-3.3 LDO regulator). Power and internet is received from a POE ...
- 41
3
votes
0
answers
446
views
DHCP with ENC28J60 on PowerLine Adaptors
I have a board based on an Atmega328 and an ENC28J60 which uses uIP.
When the board is connected to the network via a switch it can acquire an address via DHCP faultlessly. The DISCOVER, OFFER, ...
- 41
0
votes
0
answers
44
views
ENC28J60 heating issues
Here, I add the schematic and PCB layout of ENC28J60 module. It's working properly, but it's getting too hot. It's around 103 Degree Fahrenheit. How can I minimize this heating issues?
- 1
0
votes
0
answers
488
views
Compile error on the Microchip MCC generated code
I use Microchip MPLAB X MCC to generate the base application using TCP/IP lite stack for system with pic16f18346 and enc28j60 chipsets. I get the following errors. Scanning thru this error log you ...
0
votes
0
answers
104
views
How to connect a Microchip ENC28J60 to 3 port stand alone unmanaged switch chip with out using MCU
I have a working design running a Microchip PIC24 with TCP IP stack using the ENC28J60 chip. I am new to switching, and would like to add a second port for daisy chaining multiple devices without ...
- 21
0
votes
0
answers
167
views
ENC28J60 Circuit Connected With 2 Magjack in Parallel
I'm using ethernet controller chip ENC28J60 and I need to have it connected to 2 magjack in parallel, but I'm unsure if I made a correct circuit, is this can work?
Please advise me, thank you very ...
- 37
0
votes
0
answers
75
views
Why enc28j60 is not responding to another enc28j60?
I interfaced enc28j60 with atmega328p. Then I connected the enc28j60 board1 using ethernet cable to my laptop. I have checked the transmission and reception over the ethernet and it worked. I can sent ...
- 203
0
votes
0
answers
231
views
Unable to receive packets on ENC28J60
I am using a CC1352P1 launchpad from TI and trying to connect it to ENC28J60 for ethernet. I am able to transmit messages to my computer such as an ARP request, and the computer recognizes it and ...
- 103
0
votes
0
answers
235
views
ENC28J60 Custom board, heat and performance issues. need input
So since the last post I made regarding the differential line matching on a custom board HERE I have finished the board and started using it. the enc28j60 chip works as expected and i get around 2.3 ...
- 59