Questions tagged [joystick]
The joystick tag has no usage guidance.
19 questions
0
votes
1
answer
62
views
what's the name of 2 controller into 1 usb converter circuit
i had 2 game generic controller for Pc, and both of them were connected to this exact circuits and output was one USB. for my curiosity i disconnected this pcb circuit and removed the parts. but I'm ...
1
vote
0
answers
45
views
RKJXT1F42001 Logic diagram
I'm looking into integrating an RKJXT1F42001 4-directional stick switch with encoder and center push function into a keyboard I am designing, but a little confused about the diagram. I want to make ...
- 31
0
votes
0
answers
35
views
12V linear actuator with limit switches and reverse/forward Joystick
I am a 67years old fisherman from Greece. On my boot (Diesel mercedes motor) I want construct a linear actuator (from auto window wisher) to control the throtle (diesel pump).there is too many ...
0
votes
1
answer
87
views
Diode 'D2' specification and suitable replacement
I am referring to 'D2 - 3pin dual-diode (R5/IRQ7 to GND and R3/DAT to GND)' in the section 'Pinouts - Component List and Chipset Pin-Outs for Analog Joypad, SCPH-110' listed in PlayStation ...
0
votes
1
answer
98
views
Fixing SMD joystick button to PCB
I have ordered some of these small joystick buttons and I'm not sure if they will be properly fixed just with the 6 soldering points, as you do some latteral pressure to action them.
If I create a ...
- 748
2
votes
1
answer
251
views
How to connect to a PCB an arcade push buttons that is the combination of two other arcade buttons
I am building an arcade controller that has 4 buttons as Left/Down/Right/Up digital directions, and I want to add 4 other buttons that would be Down-Left, Down-Right, Up-Left and Up-Right.
All buttons ...
0
votes
0
answers
94
views
Speed control actuator in a two-actuator setup, joystick controlled
I have two 12 VDC actuators connected to a 4-position joystick.
I need to be able to control the speed of one actuator only; the other will run at full speed.
Could you draw and/or explain how I could ...
1
vote
1
answer
240
views
Hall-effect sensor joystick problem
I'm trying to control a 3-axis stepper motor motion system using a 3-axis Hall-effect sensor joystick (the APEM HF Series joystick, to be specific).
My problem is that whenever I move the joystick in ...
- 41
1
vote
1
answer
87
views
Are these trim potentiometer measurements expected? [closed]
I am trying to replace a 2-D analog joystick assembly that no longer works, because I dropped it. The assembly looks just like the one pictured in this forum post.
My question is about the trim ...
0
votes
0
answers
98
views
Adafruit Feather reading analog data incorrectly
I have some dead simple code for reading the x and y analog values from my Arduino joystick module. It works fine on my Arduino Mega 2560, but Adafruit Feather nRF52832 reads the analog signal ...
- 111
0
votes
2
answers
302
views
Question on load cell amp HX711
How do you make a load cell's amp HX711 measure both positive and negative values, or how do you set the center value for it? The main point is how to set the reference voltage (?) or something else ...
- 59
1
vote
1
answer
2k
views
can you re-center xbox one joystick potentiometer by reducing resistance between wiper and one of the pins?
Modern game consoles are beset by "joystick drift" which is due to their potentiometer's readout being unbalanced when the pot is at its physical 50% point (that is, when no force is applied ...
- 111
2
votes
1
answer
367
views
How to detect pinout of trackpoint (probably ps/2) module?
I have following trackpoint module of recent thinkpad x390.
There are some info about older modules, most useful(combined) one is: https://deskthority.net/wiki/TrackPoint_Hardware
However, i found no ...
- 151
0
votes
0
answers
266
views
Centering joystick potentiometers in a controller
I've replaced a joystick in my Dual Shock 4 controller, because it was getting stuck. The readings of the new joystick are offset to right and down.
I've read that you can recenter the readings by ...
- 157
0
votes
0
answers
207
views
Unable to read output of a joystick on a Raspberry Pi
I connected my joystick with this tutorial: link
However, it does not work. The code runs fine (after changing print "---" to ...
- 1
0
votes
1
answer
64
views
Help replacing a physical joystick for motor control with a LabView program
I'd like to start by acknowledging the similarity of this question to this one, but I really need a more basic, step-by-step explanation.
I am trying to help a student in my lab design a program to ...
- 1
2
votes
3
answers
357
views
4 Pins Potentiometer (Replacement)
I am trying to repair a very expensive manlift joystick.
It has 4 pins total, three like a normal rotary potentiometer and then a fourth across from the other three pins.
It is PEO 284-04378 Type EJ ...
- 23
0
votes
2
answers
171
views
Beginner: How to wire up a navigation button / joystick?
I have a joystick that I wish to connect to my Arduino uno. However, there's no VCC or 5V or GND pins to connect to. I do see a COM pin, but I'm unsure how I should wire that to the Arduino. My ...
- 55
0
votes
1
answer
102
views
Fail-safe joystick connection
I am looking for ideas to implement fail-safe function in joystick control box. At present, the 5V joystick HF11S10 is connected to STM32 ADC inputs via simple 5.1k:9.1k divider. We are revising the ...
- 13.1k