Skip to main content
Electrical Engineering

Return to Question

copy edit
Source Link
W5VO
W5VO
  • 19.3k
  • 7
  • 64
  • 96

Counter has notis missing an output signal

A part of design drawing

iI used a 4040 counter to count the pulsepulses from an encoder, and use 2. I then connected two counter output signalsignals to an AND gate,and and after that one way is go to reset 4040 counter, another way continuously goes to a NAND gate, but the. The issue is, that when iI connect the gates in thesethis way, there is no high voltage out putlogic-high output signal from thesethe 2 pins of the counter.but if i If I disconnect them like the image below, iI can read the output signal again from a multimeter, and other pins always have a signal. i detected

I measured the AND gate and NAND gate,gate; there are no short cutcircuits. but whyWhy there is no out putoutput signal when i connect to these gate?

the one after i changed

Counter has not output signal

A part of design drawing

i used a 4040 counter to count the pulse from encoder, and use 2 output signal to an AND gate,and after that one way is go to reset 4040 counter, another way continuously goes to a NAND gate, but the issue is, when i connect in these way, there is no high voltage out put signal from these 2 pins.but if i disconnect them, i can read the output signal again from multimeter, and other pins always have signal. i detected the AND gate and NAND gate, there are no short cut. but why there is no out put signal when i connect to these gate?

the one after i changed

Counter is missing an output signal

A part of design drawing

I used a 4040 counter to count the pulses from an encoder. I then connected two counter output signals to an AND gate, and after that one way is go to reset 4040 counter. The issue is that when I connect the gates in this way, there is no logic-high output signal from the 2 pins of the counter. If I disconnect them like the image below, I can read the output signal again from a multimeter, and other pins always have a signal.

I measured the AND gate and NAND gate; there are no short circuits. Why there is no output signal when connect these gate?

the one after i changed

added 78 characters in body
Source Link
Mark0923
Mark0923
  • 21
  • 3

A part of design drawing

i used a 4040 counter to count the pulse from encoder, and use 2 output signal to an AND gate,and after that one way is go to reset 4040 counter, another way continuously goes to a NAND gate, but the issue is, when i connect in these way, there is no high voltage out put signal from these 2 pins.but if i disconnect them, i can read the output signal again from multimeter, and other pins always have signal. i detected the AND gate and NAND gate, there are no short cut. but why there is no out put signal when i connect to these gate?

the one after i changed

A part of design drawing

i used a 4040 counter to count the pulse from encoder, and use 2 output signal to an AND gate,and after that one way is go to reset 4040 counter, another way continuously goes to a NAND gate, but the issue is, when i connect in these way, there is no high voltage out put signal from these 2 pins.but if i disconnect them, i can read the output signal again from multimeter, and other pins always have signal. i detected the AND gate and NAND gate, there are no short cut. but why there is no out put signal when i connect to these gate?

A part of design drawing

i used a 4040 counter to count the pulse from encoder, and use 2 output signal to an AND gate,and after that one way is go to reset 4040 counter, another way continuously goes to a NAND gate, but the issue is, when i connect in these way, there is no high voltage out put signal from these 2 pins.but if i disconnect them, i can read the output signal again from multimeter, and other pins always have signal. i detected the AND gate and NAND gate, there are no short cut. but why there is no out put signal when i connect to these gate?

the one after i changed

Source Link
Mark0923
Mark0923
  • 21
  • 3

Counter has not output signal

A part of design drawing

i used a 4040 counter to count the pulse from encoder, and use 2 output signal to an AND gate,and after that one way is go to reset 4040 counter, another way continuously goes to a NAND gate, but the issue is, when i connect in these way, there is no high voltage out put signal from these 2 pins.but if i disconnect them, i can read the output signal again from multimeter, and other pins always have signal. i detected the AND gate and NAND gate, there are no short cut. but why there is no out put signal when i connect to these gate?