All Questions
Tagged with conditioning signal
13 questions
1
vote
1
answer
92
views
Digital input conditioning?
I'm designing a schematic with opto-coupled digital inputs (BNC). For better noise/ground loops immunity/reflections should I add 50 ohm resistors on both input lines, signal(+) and GND, along a ...
- 71
-1
votes
2
answers
84
views
Any suggestions regarding this image i shared where a specific output voltage is required to specific input. No microcontroller should be used
Please see this image. As you can see from 0 to 999mV the output should be 0 to 100mV(this can be achieved easily) but when the input changes from 999 to 1000 and further the output should be from ...
- 71
0
votes
1
answer
80
views
Optical displacement sensor noise and current to voltage conversion
I'm currently involved in a project with the aim of measuring the tremor of mice limbs (displacements of about 100 um). The sensor my group has chosen is TCRT5000 (Vishay), but we are facing several ...
- 11
0
votes
1
answer
75
views
Current sensing using XADC
AC701 Schematics
Refer page 40 of the schematics. Here for Vccint- the regulator is switching at 250 kHz.
page 34 has the sensing signal conditioning for that the inst. amp used is INA333 which ...
- 121
0
votes
3
answers
662
views
ADC Signal conditioning. Transform 1V-4V to a 0V-5V signal, how can I do it?
Hi im doing a project for college and I got some doubts about signal conditioning. Im using a SS49E, hall sensor and, from what I have seen in the data sheets, the analog output gives values between ...
0
votes
2
answers
3k
views
Connecting multiple signals to ADC
I am designing a signal conditioning circuit which reads in data from 20 sensors and output it to the ADC of a microcontroller. My problem is I don't really understand how to connect these signals ...
1
vote
1
answer
2k
views
Op amp signal processing of an accelerometer output for an ADC
I have been designing a board which will monitor vibration activity of a machine using MEMS accelerometers. So far, I have connected the unadulterated signal from the accelerometer to the ADC however, ...
- 11
4
votes
4
answers
3k
views
Microcontroller input conditioning
I have the following circuit to condition signals reaching my microcontroller's pins.
This circuit reads both digital signals in the range 0 to 30V, and analog signals in the range 0 to 3.3V.
...
- 1,800
0
votes
1
answer
608
views
Signal conditioner for a piezoresistive pressure sensor
I have an instrumentation amplifier which output voltage equation is given.The piezoresistive pressure sensor in Figure E3.12 consists of a bridge of four silicon strain gages of 4000 ohm and 1 mV ...
user115094
1
vote
2
answers
1k
views
Type J Thermocouple Signal Conditioning to 0-5V
I've been working with signal conditioning, thermocouple out specifically. I'm working with a span of 450 °C, that is, from -50 °C to 400 °C. For those values of temperatures I get, according to the ...
user115094
0
votes
2
answers
3k
views
Arduino signal conditioning
I'm doing a project with an Arduino.
I read a voltage from a tachometer connected to a generator.
The nominal max output is 21V at 1000 rpm. The generator is managed so that the maximum tachometer ...
1
vote
1
answer
3k
views
Help for VR sensor signal conditioning (variable reluctance signal conditioning)
im trying create a CDI/TCI unit for my Suzuki Bandit GSF400. i need some help for VR sensor signal conditioning section.
this is the disc that generate the pulse signal.
i have found this image from ...
- 111
0
votes
1
answer
94
views
Confusion with output wiring and signal conditioning
I’m little confused about wiring and signal conditioning the following instrument:
http://www.skypowerinternational.com/uploads/documents/4.3351.x0.140-161_WG-Geber-firstclass-advanced_analog_eng.pdf
...
- 12.2k